Technical Data - SFA SANIMARIN 31 Notice D'installation

UK
6
GENERAL
SANIMARIN ® is a WC equipped with a pump/macerator
which installed and used correctly will give reliable and
consistent service for many years. SANIMARIN
marine or mobil unit use. Please follow these installation
instructions, paying attention to the following warnings;
« » Possible danger to personnel,
« » Warning of possible electrical hazard,
«WARNING» Possible danger of damage to the macerator.
APPLICATION
SANIMARIN uses an electronic keyboard
®
operates as follows;
• STANDARD Operation: press the NORMAL pad on the
control console. Cycle time 19 secs.
Water consumption: 2.2 lit.
• ECO Cycle: press the ECO pad on the control console.
Cycle time 10 secs.
Water consumption: 1.2 lit.
• DRAINING Cycle: press continuously the EMPTY pad on
the control console.
• Adjustment of the cycle of rinsing
The rinsing time during the "Normal" cycle can be
programmed, to add up to a further 5 seconds. The cycle
time thus varies between 19 seconds and 24 seconds, and
water consumption varies between 2.2 l and 3 l.
To enter the programming mode: press the "Normal" and
"Eco" keys at the same time for at least 5 seconds.
The red LED flashes for 5 seconds and then goes out.
To increase rinsing time by 1 second: press the "Normal"
key = 1 beep (press 5 times at most).
To reduce rinsing time by 1 second: press the "Eco"
key = 1 beep.
To exit the programming mode automatically: no keys
pressed for 5 seconds = the green LED comes on.
The water consumption programmed remains in the
memory even after the unit has been disconnected from
the power supply.
• Management of the black water holding tank
LEDs and Buzzer: Depend on the status of the "Holding
Tank" high level switch (optional connection to the electro-
6b
nic box ).
Normal level: Green LED on, red LED off. Buzzer silent and
all cycles authorized.
High level reached: Green LED off, red LED flashing =
"Full" message visible, + Beeps when a key is pressed.
3 further cycles allowed. Pressing "Normal" for 5 seconds
will return cycles to normal operation.
2
LIST OF ACCESSORIES INCLUDED
Tools required to fit a SANIMARIN
• A drill
• A jigsaw
• An electric screwdriver
3
DIMENSIONS
(see drawing n° 3 page 2)
® is for
6a
which
(see drawing n° 2)
®
4

TECHNICAL DATA

Applications
Max. vertical evacuation
Max. horizontal evacuation
Nominal power
Electrical class
Isolation level
Net weight ®
SANIMARIN 31
SANIMARIN ® 35
SANIMARIN ® 35 ST
®
SANIMARIN Bidet 35
®
SANIMARIN 48
SANIMARIN ® Elite
SANIMARIN ® Exclusive Medium 21 Kg
®
SANIMARIN Exclusive Short
CAUTION : This product should not be used for any other
purpose other than that described here. The minimum
discharge pipe inner diameter should be 19mm.
5
PERFORMANCE CURVE
1
INSTALLATION GUIDE
FIXING BOWL TO THE FLOOR
L
a – Draw the outline of the base on the floor, in the area
around the fixing holes in the ceramic bowl.
b – Measure 15 mm from the outline drawn, position the
brackets and drill through the middle of the holes.
A
c – Screw the brackets in place, leaving them loose, they
will be tightened once the bowl has been fitted.
d – Fit the bowl.
Note: wait until all the connections have been made
before fixing the bowl definitively in place.
Note: on the SANIMARIN
the front. The two screws at the back are placed vertically.
6b
CONNECTING THE WASTE PIPE AND THE WATER
SUPPLY PIPE
EVACUATION
SANIMARIN 35, SANIMARIN
®
SANIMARIN ® Elite: connect the 38/38 mm diameter bend
or the 38/25 mm diameter bend
Q
and the waste pipe, and then fix in place with clip
SANIMARIN 31: Connect the elbow diameter 35/38 mm
or the elbow diameter 38/25 mm
drainpipe (adjustable height: see diagram 6b).
Horizontal Outlet option: remove the rubber pipe from its
fitting, install the check valve
making sure that the arrow is placed uppermost, and then
fix it in place using two collars
Note: Connect the pump to the electronic box
Water supply pipe. To be connected to a seawa-
1
ter pump (supplied as an option), or to the pressurized
onboard
freshwater system. The pressure in the system must be at
least 1.7 bar.
Safety: To ensure that your installation is safe under all
heeling conditions, put a loop in the feeder and waste
pipes, with a high point 50 cm above the waterline. Fit a
ventilation valve at the high point of each loop.
Note: it is possible to fit a seawater pump other than the
pump supplied as an option, provided that the current
requirement is not more than 16 A.
6c
FITTING THE CONTROL TOUCHPAD
The touchpad must be fitted in a position where
L
it does not interfere with use of the seat and cover, and it
must not be placed more than 1.50 m from the electrical
control box .
R
Cut out a rectangle measuring 80x50 mm from the
bulkhead. Fix the keyboard in a horizontal position and
clip the frame into place.
discharge of a WC
3 m
30 m
260 W in 12 V version
260 W in 24 V version
III
IPX4
17 Kg
22 Kg
21 Kg
23 Kg
24 Kg
28 Kg
26 Kg
(see drawing n° 5 page 2)
® 35, there is only one bracket, in
35 ST, SANIMARIN
® ®
to the check valve
Q'
to the rubber
Q'
(accessory supplied),
U
, see diagram 6b.
D
.
R
48,
U
.
D
Q