Product Description And Specifications; Product Features; Technical Data - Bosch GPO 950 Professional Notice Originale

8 | English
the tool in direction opposite to the wheel's movement at
the point of snagging.
Use special care when working corners, sharp edges
u
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
Do not attach a saw chain woodcarving blade or
u
toothed saw blade. Such blades create frequent kick-
back and loss of control.
Safety Warnings specific for Polishing operations
Do not allow any loose portion of the polishing bonnet
u
or its attachment strings to spin freely. Tuck away or
trim any loose attachment strings. Loose and spinning
attachment strings can entangle your fingers or snag on
the workpiece.
Additional safety information
Wear safety goggles.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Release the On/Off switch and set it to the off position
u
when the power supply is interrupted, e. g., in case of
a power failure or when the mains plug is pulled. This
prevents uncontrolled restarting.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
1 609 92A 742 | (24.11.2021)
Intended Use
The power tool is intended for polishing metal and coated
surfaces.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Speed preselection thumbwheel
(2) On/off switch locking mechanism
(3) On/off switch
(4) Guard plate
(5) Auxiliary handle (insulated gripping surface)
(6) M14 adapter
(7) M16 adapter
(8) Adhesive disc (M16)
(9) Flat polishing sponge
a)
(10) Lambswool pad
(11) Wavy set polishing sponge
(12) Polishing disc with sponge
(13) Open-ended spanner (2x)
(14) Handle (insulated gripping surface)
(15) Direction of rotation arrow on housing
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Polisher
Article number
Rated power input
Power output
Rated speed
Speed adjustment range
Max. polishing disc diameter
Thread size adapter
Soft start
Speed preselection
Constant electronic control
Weight according to EPTA-Pro-
cedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Fitting
Fitting Protective Equipment
Pull the plug out of the socket before carrying out any
u
work on the power tool.
a)
a)
GPO 950
3 601 CA2 0..
W 950
W 539
-1
min 2100
-1
min 600–2100
mm 180
M 14/M 16
●
●
●
kg 2.3
/ II
Bosch Power Tools