Overview; Special Product Features; Initial Operation; Side Handle Installation - Metabo BE 710 Mode D'emploi

170267550_0208 BE 710.book Seite 12 Donnerstag, 31. Januar 2008 10:45 10
ENGLISH
ENG
event of a power failure. Not required for drills with
VTC electronics (restart protection).
Keep hands away from the rotating tool!
Remove chips and similar material only with the
machine at standstill.
Wear ear muffs when working for long periods
of time. High noise levels over a prolonged period
of time may affect your hearing.
Caution with hard screwdriving (driving of screws
with either a metric or an imperial thread into steel)!
The head of the screw may rip off or high restoring
torques may be incurred at the handle.
Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust may
cause allergic reactions and/or respiratory
diseases to the operator or bystanders.
Certain kinds of dust are classified as carcinogenic
such as oak and beech dust especially in conjunc-
tion with additives for wood conditioning (chromate,
wood preservative). Material containing asbestos
must only be treated by specialists.
- Where the use of a dust extraction device is
possible it shall be used.
- The work place must be well ventilated.
- The use of a dust mask of filter class P2 is
recommended.
Follow national requirements for the materials you
want to work with.

5 Overview

See page 3 (please unfold).
1 Geared chuck*
2 Futuro Plus keyless chuck *
3 Futuro Top keyless chuck*
4 Thumb-wheel for speed selection
5 Electronic signal indicator*
6 Lock button
7 Speed preselection wheel*
8 Trigger
9 Rotation selector switch
10 Side handle
* depending on machine type

6 Special Product Features

Metabo S-automatic safety clutch:
If the insertion tool jams or hooks, the power flow to
the engine will be restricted. Because of the high
power which then arises, always hold the machine
with both hands on the handles, stand safely, and
concentrate on your work.
Turn-off carbon brushes: If the brushes are
completely worn, the machine switches off
automatically.
12
With VTC electronics: A LED warns before the
brushes are completely worn.
Restart protection with VTC electronics:
(BE 1020)
The restart protection prevents the machine from
starting unintentionally when being plugged in
again or when power is restored after a power
failure.
Overload protection indicator with VTC
electronics:
(BE 1020)
The overload protection indicator issues a warning
if the machine is overloaded.

7 Initial Operation

Before plugging in, check to see that the
rated mains voltage and mains frequency,
as stated on the rating label, match with your
power supply.
To ensure that the drill chuck is securely
fitted: After initial drilling (clockwise), use a
screwdriver to tighten the safety screw firmly
inside the drill chuck. This safety screw is model-
specific and as such may not be in all models. THE
SAFETY SCREW HAS A LEFT-HANDED THREAD!
(see section 8.8)
7.1

Side handle installation

For safety reasons, always use the side
handle supplied.
Open the clamping ring by turning the side handle
(10) counter-clockwise. Place the side handle onto
the machine's collar. Tighten the side handle in the
required angle depending on the task at hand.

8 Use

8.1

Switching On and Off

To start the machine, press the trigger (8).
The speed can be changed at the trigger.
The electronic soft start means that the machine
accelerates continuously up to the pre-selected
speed.
For continuous operation the trigger can be locked
with the lock button (6). To stop the machine,
press the trigger again.
If switched on continuously, the machine
continues running if it is jerked out of your
hands. Therefore, always hold the machine
with both hands on the handles, stand safely,
and concentrate on your work.