NEFF T4 D 0 Série Notice D'utilisation page 5

Masquer les pouces Voir aussi pour T4 D 0 Série:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 49
Installation Instructions
en
Important notes
S Safety in use is only guaranteed if the technical installation of
the hob has been carried out correctly and in accordance with
the installation instructions. The installation technician shall be
liable for any damage caused as a result of incorrect installation.
S Only an authorised technician is able to connect the appliance.
The guidelines set out by the local electricity provider must be
observed.
S This is a class I appliance and should only be used with an
earthed connection.
S Using this appliance without an earth connection or after it has
been incorrectly installed may, in very rare cases, cause serious
harm.
The manufacturer accepts no responsibility for any malfunction
or damage which is caused by incorrect electrical installation.
S If the appliance is not fitted with an accessible plug,
disconnecting means must be incorporated in the fixed
installation, in accordance with the installation regulations.
S The inlet hose must be positioned so that it does not touch any
of the hot parts of the hob or oven.
S Any change to the appliance's interior, including changing the
power cable, must be performed by the Technical Assistance
Service.
S Induction hobs may only be installed over drawers, ovens of
the same brand with forced-air ventilation, or dishwashers of the
same brand. Refrigerators, unventilated ovens, and washing
machines may not be installed beneath the hob.
Assembly over drawer (figure 2a)
S If the hob is installed above a drawer, metal objects stored
inside could become very hot due to the air recirculating from the
hob ventilation system. If this occurs, an intermediate support is
recommended.
A wooden panel can be used as an intermediate support (figure
3), or you may order a suitable accessory from our Technical
Assistance Service.
The reference code for this accessory is 686002.
S The working surface upon which the hob is installed must be
at least 20 mm thick.
S The space between the top of the working surface and the top
of the drawer must be 65 mm.
Assembly over oven (figure 2b)
S The working surface upon which the hob is installed must be
at least:
- 20 mm thick if installed over a compact oven.
- 30 mm thick if installed over a full-size oven.
S If the hob is installed over a compact oven, there must be 60
mm of space between the top of the oven and the top of the
working surface.
Assembly over dishwasher (figure 2c)
S If the hob is installed over a dishwasher, an intermediate
accessory must be installed. The accessory may be ordered
from our Technical Assistance Service.
The reference code for this accessory is 686002.
S The working surface upon which the hob is installed must be a
minimum of 20 mm and a maximum of 40 mm thick.
S The space between the top of the working surface and the top
of the dishwasher must be:
- 60 mm if installed over a compact dishwasher.
- 65 mm if installed over a full-size dishwasher.
Installing and connecting the hob
Figure 1/2/3/4/5
S See the rating plate for the voltage.
S Connect according to the connection diagram only.
Connection drawing - Figure 5
1. Brown
2. Blue
3. Yellow and green
Changing the connection current
10 / 13 / 16 / 20 Amps - Figure 6
Before using the hob for the first time, it must be tested for the
correct current.
Follow the steps below to change the current of the hob:
1 - Turn on the hob with the main switch.
Do not place any pans on the hotplates
2 - Within the following 60 seconds, adjust all hotplates to the
desired power level according to the required connection current
(see table).
Power level
Connection current in amperes
b
20 A
c
16 A
d
13 A
10 A
3 - Turn off all the hotplates in sequence, starting from the lower
right and continuing counter-clockwise.
4 - The selected connection current is indicated in the display of
the right-hand, lateral hotplates.
5 - Turn off the hob with the main switch.
The selected connection current will have been properly saved.
Removing the hob
S Disconnect the cooker from the power supply.
S Push out the hob from below.
5

Publicité

Table des Matières
loading

Table des Matières