Güde 40088 Traduction Du Mode D'emploi D'origine page 16

Warranty does not cover unprofessional use such as
device overload, violent use, damage caused by third party
or foreign materials, failure to comply with operations and
assembly manual, and normal wear and tear.
Residual risks and protective measures
Inappropriate local lighting
Inadequate lighting represents a high safety risk
Appropriate lighting should always be provided when
working with the appliance.
Disconnect the appliance from compressed air and store it
properly.
Behaviour in case of emergency
Provide necessary first aid treatment corresponding to the
injury nature and seek qualified medical help as soon as
possible. Protect the injured person from other injuries and
calm him/her down.
First aid kit must always be available in the place of
your work in case of accident in accordance with DIN
13164. Material taken out of the first aid kit needs to be
supplemented right away.
If help is needed,
please provide the following details:
1. Place of accident
2. Accident nature
3. Number of injured persons
4. Injury type
Disposal
The disposal instructions are based on icons placed on the
appliance or its package. The description of the meanings
can be found in the "Marking" chapter.
Transport package disposal
The package protects the appliance against damage
during transport. Packing materials are usually chosen
depending on their environmental friendliness and disposal
method and can therefore be recycled.
Returning the package to material circulation saves raw
materials and reduces waste disposal costs.
Parts of packages (e.g. foils, styropor) can be dangerous
to children. Risk of suffocation!
Keep parts of packages away from children and dispose
them as soon as possible.
Operating staff requirements
The operator must carefully read the Operating
Instructions before using the appliance.
Qualification
No special qualification is necessary for using the
appliance apart from detailed instruction by an expert.
Minimum age
The appliance can only be operated by persons over 16
years of age. An exception includes youngsters operating
the appliance within their professional education to achieve
necessary skills under trainer's supervision.
Training
Using the appliance only requires appropriate instructions
by a professional or reading the Operating Instructions. No
special training necessary.
Servicing
Do you have any technical questions? A claim? Do you
need spare parts or the Operating Instructions?
You will be helped quickly and without needless
bureaucracy at our webpage www.guede.com in the
Services part. Please help us be able to assist you. To be
able to identify your appliance when claimed, we need to
know its serial No., order No. and year of production. All
these details can be found on the type label. Enter the
details below for future reference.
Serial No.:
Order No.:
Year of production:
Tel.: +49 (0) 79 04 / 700-360
Fax: +49 (0) 79 04 / 700-51999
E-Mail: support@ts.guede.com
Troubleshooting
At all failures it is first necessary to check whether the
appliance is sufficiently and permanently supplied
with pneumatic oil.
Failure Cause
Compressed air
• O-rings are
leaking from the
damaged or
cover hole
dirty, which has
been caused by
a foreign item.
Compressed air
• O-rings are
leaking from the
damaged or the
valve
valve is faulty.
Compressed air
• Screws are
leaking between
loosened. O-
the body and
rings are
cylinder cover
damaged.
Piston not fully
• Appliance
returning, idle
placed too
strokes
weakly or too
shortly.
• Piston dragging
as it is not
lubricated.
• O-ring is faulty.
Nails not fully
• Air pressure too
fired
low.
• Hose piping with
a too small
cross section.
• Appliance not
lubricated.
• Firing
mechanism
worn out.
Failure Cause
Nails breaking
• Firing
and overlapping
mechanism
Removal
• Clean or
replace the O-
rings.
• Replace the O-
rings and valve.
• Tighten the
screws.
Replace the O-
rings.
• Place the
appliance
stronger.
• Lubricate the
cylinder surface
contact.
• Replace the O-
ring, check the
operating
pressure.
• Gradually
increase the
pressure by 0.5
bar to make
sure nails are
fired properly.
• Hose piping
inner diameter
at least 6 mm.
• Clean and
lubricate the
parts.
• Grind the firing
mechanism
down by app.
0.2 mm.
Removal
• Replace the
firing