Fontanot genius q 010 Instructions De Montage page 11

Final assembly
35. To further reinforce the staircase at intermediate points, fix components 033010 to wall and join to the
balusters, using components 033056. Drill with an 8 mm bit and use components 008004, 011053,
011057, 005035 (Fig. 11).
Assembly of 030 railing
36. Fit parts BE6 into holes on treads with edge facing upwards (Fig. 2).
37. Starting from the top, fit balusters 122011, with parts BE5 and 002040, onto corner treads with a height of
about 99 cm.
38. Cut a piece of baluster 122011 to length to obtain spacers to connect treads. Insert lateral connection
spacers and secure with components 001013 at top and at bottom.
39. Definitively tighten component 005008 (Fig. 5).
40. Cut sections of handrail 140010 to length; assemble with part 046011. For optimal fixing, the handrail must
follow about 1/8 of a turn from the contact point.
41. Fix handrail to balusters with parts 002031; keep balusters vertical. Insert angle parts 031061, 031071
and 031072 with screws 012014 and 001017 for changes of direction. Apply end caps 031061 to ends of
handrail with parts 004034 and 011069 (Fig. 2) (Fig. 12).
42. Fix component BE5 to the floor using an Ø 8 mm bit and so that it corresponds to the first baluster. Use
elements 011053, 008004, and 001004 (Fig. 2). Assemble the reinforcing component 046050.
43. Determine position of intermediate balusters. Drill with a 4.5 mm bit; assemble parts BE5 with screw
002040.
44. Cut intermediate balusters at a height that can be determined on the staircase itself. Insert balusters in
parts BE5, tighten components 001004 and fix to handrail with parts 002031; keep balusters vertical (Fig. 2)
(Fig. 12).
Assembly of 030 balustrade
45. Screw component 033063 on to brace 046036 with the 011038 screws (Fig. 2). Assemble the 121028 post
with the 033149 fixing component and items 011063 and 005036, insert it into component 033063 and fix
it with items 001004, positioning the 033149 tie according to the direction of the handrail.
46. Position components 033008 on landing, using components 002040 and 001004. Drill landing with a 4.5
mm bit, keeping a distance between centres of no more than 12 cm.
47. Position balusters 122014 and tighten component 001004 (Fig. 2).
48. Fix straight handrail 140010 using components 002031 (Fig. 2).
49. Depending on position and presence of walls around the stairwell, it may be necessary to position one or two
extra balusters 122014.
50. In this case, a space must be considered that is at the same distance from the other balusters or from the
wall. Drill landing with a 5 mm bit and assemble with components 033008, 001004 and 002040 (Fig. 2).
51. Assembly of floor-mounted balustrade, if applicable (Fig. 13)
Determine the position of the posts on the floor, on average one every 12 cm and at a distanza of 8 cm from
the edge. Drill with a Ø 10 mm bit and insert the 046010 components, fixing them with chemical resin (not
supplied). Assemble components 033008 with components 009002 and 005001. Fix the first balustrade
balusters (H= 910 mm) using component 033010 and items 008004, 011053 and 033046 (drill with an Ø
8 mm bit). Insert the remaining 122014 balustrade balusters (H= 910 mm) into the 033008 components,
with the 126009 reinforcing baluster about every metre, and lock them with components 001004. Assemble
the 140010 handrails to the balusters with the 002031 components using item 046011. Assemble any
031061, 031072, 031071 connecting components and the 031061 terminal components.
Final assembly
52. To further reinforce the staircase at intermediate points, fix components 033010 to wall and join to the
balusters, using components 033046. Drill with an 8 mm bit and use components 008004, 011053,
011057, 005035 (Fig. 12).
11 - Genius 030 - 040 Q