General Information; Accessories - Novy Vision 7835 Instructions D'installation

Hang the extraction hood over the mounting brackets.
7
Grasp the underneath of the glass plate (A) at the left and right and pull it firmly forwards. Open the glass plate so that
8
the grease filter is visible. You can remove the metal grease filter (B) from the hood.
9
There are 2 holes on the inside of the hood. Mark these holes on the wall. Depending on the wall, you can position the
screws directly in the wall or remove the hood from the wall first, drill the holes, and use the plugs and screws. After
this, replace the hood in the brackets and fasten the hood to wall with the 2 screws.
10
• Place the exhaust pipe on a connection nozzle using aluminium tape or a hose clamp.
• Put the plug into the wall socket.
11
Take the two shaft parts and place them onto the wall-mounted chimney hood. Make sure that this is done carefully
in order to prevent the chimney hood or the shafts from being damaged. Screw the upper shaft tight to the spacer
bracket with 2 screws.
Mount the remote motor unit
For the model 7835 the remote motor unit of the chimney hood is mounted. A choice can be made between an internal
motor, an external motor for outside mounting or a roof motor. With an external motor the minimum distance between
the hood and the external motor must be 5 metres. The hood is connected to an earthed wall socket. The hood and the
motor unit are electrically connected by means of a 6-pole plug connection. Additional information can be found in the
mounting instructions of the motor involved.
Install the exhaust duct
The motor outlet has a diameter of 150 mm. It is recommended to connect an exhaust duct with a diameter of 150 mm
to this.
For optimum performance of the hood it is important to pay attention to the points given below.
Circular ducts:
• Use smooth, non-flammable pipes with an internal diameter that is equal to the external diameter of the connection
nozzle of the hood. Maximally extend flexible ducts and cut them to size.
• Do not reduce the exhaust diameter. This will lower the capacity and raise the noise level.
• When connecting to a short exhaust duct, it may be required to mount a non-return valve in the duct to avoid wind
blowing in.
• Use a hose clamp or aluminum tape for airtight connections.
• In case of an exhaust pipe through the wall, use a wall vent.
Flat duct:
• Use flat duct with rounded corners and with air deflectors. Available at Novy.

General information:

• Make the duct as short as possible and with as few as possible bends to the outside.
• Avoid square bends. Use rounded bends for proper air conduction.
• In case of an exhaust pipe through the outside wall passing a cavity wall, make sure that the exhaust duct fully bridges
the cavity and slightly declines to the outside.
• In case of an exhaust pipe through the roof, use a double-walled roof passage with sufficient width.
• Never connect to a flue duct.
Make sure that sufficient air is supplied. Fresh air can be supplied by slightly opening a window or an outside

ACCESSORIES

InTouch kit incl. remote control (article 990021)
InTouch offers you the possibility of controlling the Novy cooker hood from the Novy InTouch induction cooking plate. The
kit is fitted in the hood after which it is immediately possible to control the hood using the controls on the Novy InTouch
induction cooking plate. A standard remote control is supplied with the kit that can be used on the hood immediately.
It is recommended to mount the inTouch kit before mounting the hood. The kit must be installed by an authorised person.
Various accessories
• Clamp Ø60-215 mm
• Aluminium tape (per 50 m)
• Aluminium wall vent for outlet Ø150mm
• Mechanical wall vent Ø150mm
• One-way valve Ø150mm
• Stainless steel cleaner
Characteristics of the product on condition of changes or printing errors, February 2018
906291
906292
906178
906419
906432
906060
EN 14