Normal Washer Sounds; Options; Button Sound; Modifiers - Whirlpool WHP1000SQ Guide D'utilisation Et D'entretien

Drain/Spin
Use this cycle to drain your washer or to drain and spin your
wash load. The spin speed is preset to High. If desired, you can
reduce the spin speed by selecting the speed you want from the
SPIN SPEED modifier.
NOTE: Loads of synthetics, delicate fabrics, hand washables,
and woolens should be drained with no spin or low spin speed
to avoid fabric stress.

Normal Washer Sounds

As with any new product, you will hear sounds that you are not
accustomed to. You may hear various sounds when the door is
locked and unlocked, and during the washing, rinsing, and
spinning process. Between changes in wash actions, there will
be momentary pauses. You will hear water spraying and
splashing during the wash and rinse cycles. These new sounds
and pauses are part of normal washer operation.
You can customize your wash by adding options to your cycle
selections. You can add or change an option after starting a cycle
anytime before the selected option begins. Not all options are
available with all cycles. Available options will glow amber.
Current selections will glow green. If an option is unavailable with
a selected cycle, the light will not illuminate.
See the "Laundry Guide" for an overview of possible options
for each Wash Cycle selection.
You can select more than one option for a cycle. Some
options cannot be added to some cycles. For example, Deep
Clean cannot be added to the Quick Wash cycle.
If an option is unavailable with a selected cycle, there will be
3 short tones, and the light for that option will not glow when
selected.
Delay Wash
To begin the wash cycle later, select DELAY WASH until the
desired delay time (in hours) shows in the Estimated Time
Remaining display, and then select START. The countdown to the
wash cycle will show in the display window, and the button
indicator will blink until the cycle begins.
IMPORTANT: When delaying a cycle, use only powdered
detergents in the high efficiency "HE" detergent compartment
since liquid detergents may seep out of the compartment during
Delay Wash, before the wash cycle begins.
16

Options

Clean Washer Reminder
The Clean Washer Reminder light illuminates to remind you to
use the Clean Washer cycle regularly. The reminder light will
illuminate every 30 cycles. The reminder light may be reset by
either running the Clean Washer cycle, or by pressing the CLEAN
WASHER RESET button.
Deep Clean with Steam
Use this option for heavily soiled loads that need improved stain
treatment, loads with multiple types of stains, or loads you
suspect as having stains, but are afraid may have been missed
(no sorting or searching for stains). When Deep Clean with Steam
is selected, the water temperature of the selected wash cycle is
automatically set to warm. The water will then be slowly heated
to the temperature selected, along with steam, to aid in stain
removal. This option will provide optimal removal of organic
stains such as blood and grass.
Extra Rinse
An extra rinse can be used to aid in the removal of detergent or
bleach residue from garments. This option provides an additional
rinse with the same water temperature as the first rinse.
Cycle Signal
This signal is helpful when you are removing items from the
washer as soon as it stops. Press CYCLE SIGNAL to select Loud,
Soft, or Off.

Button Sound

Button sounds are used to notify you of what has been selected
or to let you know when something is not available. Press
BUTTON SOUND to select Loud, Soft, or Off.

Modifiers

Preset cycle settings of Water Temperature, Spin Speed, and Soil
Level can be changed. You can change a modifier after starting a
cycle anytime before the selected modifier begins. Not all
modifiers are available with all cycles and options. Available
options will glow amber. Current selections will glow green. If a
modifier is unavailable with a selected cycle, the light will not
illuminate.
NOTE: The panel shown below may be different from that of your
model.
To change the water temperature, select the WATER TEMP
button until the desired setting glows green.
To change the spin speed, select the SPIN SPEED button
until the desired setting glows green.
To change cycle time, select SOIL LEVEL button until the
desired setting glows green.