Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
b. DMX512 Connection
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-
pin XLR input of the VDP1001RGYLD9. Multiple VDP1001RGYLD9s can be linked through serial linking. The linking
cable should be a two-core screened cable with XLR input and output connectors.
c. DMX512 Chain with Termination
d. DMX Start Address
All DMX-controlled devices need a digital start address so that the correct device responds to the signals. This start
address is the channel number from which the device starts to "listen" to the DMX controller. Enter the correct
number and read it from the display located on the base of the VDP1001RGYLD9.
You can use the same starting address for a whole group of devices or enter an individual one for every device.
When all devices have the same address, all the VDP1001GRYLD9s will "listen" to the control signal on one
particular channel. In other words: changing the settings of one channel will affect all devices simultaneously. If you
set different addresses, each device will "listen" to a separate channel number. Changing the settings of one channel
will only affect the device in question.
In the case of the 9-channel VDP1001RGYLD9, you will have to set the start address of the first VDP1001RGYLD9
to 1, the second VDP1001RGYLD9 to 10 (1 + 9), the third to 19 (10 + 9) and so on.
First, use the selector switch (#8 at the back of the device) to select the working mode: remote control, DMX / slave,
sound-active or auto mode.
The DMX start address is defined by the first 9 DIP switches. The encoding is binary: DIP n° 1 is value 1, DIP n° 2 is
value 2, DIP n° 3 is value 4, DIP n° 4 is value 8, etc. Example: If the start address should be 95, the settings would
be as follows: 111110100 (1 + 2 + 4 + 8 + 16 + 0 +64 + 0 + 0 = 95).
DIP switch 10 is used to select the master or the slave mode. The master mode can be set to sound-active or auto
mode. Slave mode can be set to DMX or slave mode. Use DIP switch 9 to set the sound-active or auto mode in a
master device.
Depending on how you wish to control the projector, you will need to assign the correct DIP switch address according
to the chart below (0 = off, 1 = on, X = on or off):
1
2
3
4
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Set DMX address
X
X
X
X
X
X
X
X
e. The Remote Control
• LASER ON/OFF
Switch the VDP1001RGYLD9 on and off.
VDP1001RGYLD9_v2
A DMX terminator is recommended for installations where the DMX cable has to run a
long distance or is in an electrically noisy environment (e.g. discos). The terminator
prevents corruption of the digital control signal by electrical noise. The DMX terminator is
simply an XLR plug with a 120 resistor between pins 2 and 3, which is then plugged into
the XLR output socket of the last device in the chain.
Please see illustrations.
DIP switch chart
5
6
7
8
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
9
10
11
12
X
0
0
0
X
0
0
1
X
0
1
0
X
0
1
1
X
1
0
0
1
0
1
X
1
1
0
X
1
1
1
6
Function
Sound active mode
Auto mode
Master sound mode
Master auto mode
Slave mode
DMX mode
Test mode
Remote mode
VELLEMAN
Publicité
Table des Matières
