stayer CP190C Instructions D'emploi page 17

CERTIFIES
That the machine:
Type:
CIRCULAR SAW
Models: CP190C - CP236 - CH185C
I declare under our responsibility that the product
described under "Technical Data" is in accordance with
the following standards or standardized documents: EN
60745-1, EN 60745-2-5, according to regulations 2011/65/
UE, 2004/108/CE, 2014/30/UE, 2006/42/CE.
Ramiro de la fuente
Managing Director
Assembly
Mounting/Replacing the Saw Blade
- Before any work on the machine itself, pull the
mains plug.
- When mounting the saw blade, wear protective
gloves. Danger of injury when touching the saw
blade.
- Only use saw blades that correspond with
the characteristic data given in the operating
instructions.
- Do not under any circumstances use grinding
discs as the cutting tool.
Selecting a Saw Blade
An overview of recommended saw blades can be found at
the end of this manual.
Removal of the Saw Blade (see figure A)
For changing the cutting tool, it is best to place the machine
on the face side of the motor housing.
- Press the spindle lock button 4 and keep it pressed.
- The spindle lock button 4 may be actuated only when
the saw spindle is at a standstill.
Model CH 185 C: To lock the disc apply the key pivots
in the washer 19.
Otherwise, the power tool can be damaged.
* With the Hex key 17, unscrew the clamping bolt 18
turning in rotation direction 1.
* Tilt back the retracting blade guard 11 and hold firmly.
* Remove the clamping flange 19 and the saw blade
20 from the saw spindle 22.
Mounting the Saw Blade (see figure A)
For changing the cutting tool, it is best to place the machine
on the face side of the motor housing.
- Clean the saw blade 20 and all clamping parts to be
assembled.
- Tilt back the retracting blade guard 11 and hold firmly.
- Place the saw blade 20 on to the mounting flange 21.
The cutting direction of the teeth (direction or arrow on
saw blade) and the direction-of-rotation arrow on the
blade guard 15 must correspond.
ENGLISH
17
- Mount the clamping flange 19 and screw in the clamping
bolt 18 turning in rotation direction 2. Observe correct
mounting position of mounting flange 21 and clamping
flange 19.
- Press the spindle lock button 4 and keep it pressed.
- With the Hex key 17, tighten the clamping bolt 18 turning
in rotation direction 2. The tightening torque is between
6–9 Nm, which corresponds to hand tight plus ¼ turn.
Dust/Chip Extraction
- Before any work on the machine itself, pull the
mains plug.
January 5, 2016 - Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful
to one's health. Touching or breathing-in the dusts
can cause allergic reactions and/or lead to respiratory
infections of the user or bystanders. Certain dusts, such
as oak or beech dust, are considered as carcinogenic,
especially in connection with wood-treatment additives
(chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
* As far as possible, use a dust extraction system
* Provide for good ventilation of the working place.
* It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
- Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Mounting the Extraction Adapter (see figure B)
Attach the extraction adapter 23 onto the chip ejector 14
until it latches. A vacuum hose with a diameter of 35 mm
can be connected to the extraction adapter 23.
- The extraction adapter may not be mounted when no
external dust extraction is connected. Otherwise the
extraction channel can become clogged.
- Do not connect a dust bag to the extraction adapter.
Otherwise the extraction system can become clogged.
To ensure optimum extraction, the extraction adapter 23
must be cleaned regularly.
External Dust Extraction
Connect the vacuum hose to a vacuum cleaner
(accessory).
An overview for connecting to various vacuum cleaners
can be found at the end of this manual.
The machine can be plugged directly into the receptacle
of a STAYER all-purpose vacuum cleaner with remote
starting control.
The vacuum cleaner starts automatically when the
machine is switched on.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Operation
Operating Modes
- Before any work on the machine itself, pull the mains
plug.
Adjusting the Cutting Depth (see figure C)
- Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
17
suitable for the material.