Cutting Height Adjustment; Starting And Stopping - Gardena PowerMax 32 E Mode D'emploi

Masquer les pouces Voir aussi pour PowerMax 32 E:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 17
16. Remove the plug from the mains :
-
before leaving the product unattended for any period
-
before clearing a blockage
-
before checking, cleaning or working on the appliance
-
if you hit an object. Do not use your product until you are
sure that the entire product is in a safe operating condition.
-
if the product starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
Where to Use Your GARDENA PowerMax 32 E Mower
The GARDENA mower is designed for cutting lawns in
and around the garden.
Do not use the mower on a slope steeper than 20
maximum.
The Loose Parts Pack is packaged underneath the deck.
Assembly of Lower Handles to Deck
1. Place the bolt A2 through the hole in the lower handle
A1 until the lower handle fits into the recess A3
2. Place the washer B1 and the wing knob B2 on to
the bolt and tighten the wing knob. It may take 20 - 25
turns to fully tighten on initial assembly.
3. Repeat on the other side.
Assembly of Upper Handle to Lower Handle.
1. Ensure the upper handle is located correctly with the
lock-off button on the switchbox uppermost.
2. Ensure the upper handle C1 and the lower handle
C2 are aligned correctly.
3. Fit the bolt C3 , washer C4 and wing knob C5 .
Tighten the wing knob.
Fitting Fully Assembled Grassbox to Lawnmower.
1.
Lift safety flap G1
2.
Make sure the discharge chute is clean and free
from debris G2
3.
Locate fully assembled grassbox onto 2 location
points G3 at the rear of the deck as illustrated in
pic. H
4.
Locate safety flap onto the top of the grassbox.
Ensure the grassbox is securely located.
Height of cut is adjusted by raising or lowering the
wheels using the height adjustment lever J1
There are five heights of cut on this product
20 - 60 mm .
To Start your Lawnmower
1. Attach the extension cable to the back of the
switchbox. K
2. Form a loop in the cable and push the loop through
the slot. L
3. To secure, position the loop over the hook and pull the
cable back through the slot M .
4. Connect the plug to the mains and switch on.
The switchbox is provided with a lock-off button N1 to
prevent accidental starting.
5. Press and hold the lock-off button N1 on the
Safety
Maintenance and storage
1. Caution: Do not touch rotating blade s
2. Keep all nuts, bolts and screws tight to be sure the
3. Check the grassbox frequently for wear or deterioration.
4. Replace worn or damaged parts for safety.
5. Only use the replacement parts specified for this product.
6. Be careful during adjustment of the product to prevent
7. Store in a cool dry place and out of reach of
To prevent injury, the mower must not be used for
trimming bushes, hedges, shrubs, for cutting and pruning
of climbers or grass on roofs or in balcony boxes. In
addition, the mower must not be used for chopping up
branches, twigs or for levelling irregularities in the soil.
Assembly Instructions
4. Repeat on the other side.
5. Fit the cable to the handles with the clips provided.
Make sure the cable is not trapped between the upper
and lower handles.
Grassbox Assembly
1. Slide the grassbox tongue into the slots in the
grassbox lower until it clicks securely into position D
2. Push the grassbox handle into the slots in the
grassbox upper until it clicks securely into position. E
3. Starting at the rear of the grassbox, locate the
grassbox upper into the grassbox lower by aligning
the clips F1 . Ensure all clips are correctly located
before clicking into position.
4. Clip the two halves together, ensuring all clips are
securely connected.
Grassbox

Cutting Height Adjustment

NOTE
A medium height of cut is recommended for most
lawns. The quality of your lawn will suffer and
collection will be poor if you cut too low.

Starting and Stopping

switchbox, then squeeze one of the Start/Stop levers
towards the upper handle P .
6. Continue to squeeze the start/stop lever towards the
upper handle and release the lock-off button Q .
NOTE - There are two start/stop levers fitted. Either
one can be used for starting the lawnmower.
IMPORTANT - Do not use the start/stop levers
intermittently
To Stop your Lawnmower
1. Release the pressure on the Start/Stop lever.
ENGLISH - 2
product is in safe working condition.
entrapment of the fingers between moving blades and
fixed parts of the machine.
children. Do not store outdoors.
IMPORTANT
AFTER FITTING ENSURE NO
GAP REMAINS BETWEEN THE SAFETY FLAP
AND THE GRASSBO .
Removal is the reverse procedure.
For larger areas of grass where grass collection is
not required you can use your lawnmower without
the grassbox. Ensure the Safety Flap is fully closed.
The design of the safety flap permits the cut grass
to be discharged downward behind the machine.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

4073

Table des Matières