Product Description And Specifications - Bosch GWS Professional 20-230 H Notice Originale

OBJ_BUCH-1686-004.book Page 18 Thursday, October 13, 2016 4:04 PM
18 | English
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for cutting, roughing and brushing of
metal and stone materials without the use of water.
For cutting with bonded abrasives, a special cutting guard
(accessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
With approved sanding tools, the machine can be used for
sanding with sanding discs.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Spindle lock button
2 On/Off switch
3 Auxiliary handle (insulated gripping surface)
4 Grinder spindle
5 Protection guard for grinding
6 Locking screw for protection guard
7 Mounting flange with O-ring
8 Grinding wheel*
9 Clamping nut
10 Two-pin spanner for clamping nut*
11 Quick-clamping nut
12 Carbide grinding head*
13 Protection guard for cutting*
14 Cutting disc*
15 Protection guard for grinding cup*
16 Grinding cup*
17 Two-pin spanner, offset, for grinding cup*
18 Hand guard*
19 Spacer discs*
20 Rubber sanding plate*
21 Sanding sheet*
22 Round nut*
23 Cup brush*
24 Cutting guide with dust extraction protection guard *
25 Diamond cutting disc*
26 Handle (insulated gripping surface)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
1 609 92A 2C7 | (13.10.16)
Technical Data
Angle Grinder
GWS ...
Article number
3 601 ...
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of
grinder spindle
Restarting Protection
Reduced starting current
Weight according to EPTA-
Procedure 01:2014
– with vibration-damping
auxiliary handle
– with standard-auxiliary
handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles
generate brief voltage drops. Interference with other equipment/ma-
chines may occur in case of unfavourable mains system conditions.
Malfunctions are not to be expected for system impedances below
0.25 ohm.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
*
Typically the A-weighted noise levels of the product are:
Sound pressure level 92 dB(A); Sound power level
103 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
determined according to EN 60745-2-3:
Surface grinding: a
Disk sanding: a
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
20-230
H
... H50 L.. ... H50 M..
W 2000
W 1250
-1
min 6600
mm 230
M 14
mm 25
–
–
kg 5.2
kg 5.1
/II
(triax vector sum) and uncertainty K
h
2 2
=7.5 m/s , K=1.5 m/s ,
h
2 2
=4.0 m/s , K=1.5 m/s .
h
Bosch Power Tools
20-230
JH
2000
1250
6600
230
M 14
25


5.2
5.1
/II