Environment Protection; Connecting The Machine - Electrical Connections; Noise Information; Earthing Instructions - PEUGEOT EnergyBand-150 Manuel D'utilisation

The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the
product end-of-life. This applies to your device but also to any accessories marked with this symbol. do not dispose of these
products as unsorted municipal waste.
In accordance with the WEEE directive concerning the environment, it is forbidden to abandon used electric or electronic equip-
ment or leave them at a standard public dump. The equipment must be taken to a collection point for treatment, recovery and
recycling of EEE waste, or returned to its dealer on a 1 for 1 basis (one item of equipment bought for one item of equipment ta-
ken back). The user is therefore taking an environmentally-friendly step and helping to preserve natural resources and protect
human health.
EXTENSION CORDS
Only use extension cords with three conductors ending in two-pin plugs and sockets with two holes and an earth pin that are suited to the
plug of the tool. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry
the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing
the motor to overheat. Use the chart provided below to determine the minimum wire size required in an extension cord. Only round jacke-
ted extension listed by laboratories should be used.
Length of extension cord: up to 15 m
Wire size: 3 x 2.5 mm2
Before using an extension cord, inspect it for loose or exposed wires and cut or worn insulation. Repair or replace any damaged or worn
cord immediately.
ELECTRICAL CONNECTIONS
Your machine has a precision built electric motor. It should be connected to a power supply that is 230 V, 50 Hz. If your tool does not ope-
rate when plugged into a socket, double-check the power supply characteristics.
Le niveau de bruit de la machine est mesuré selon la norme DIN EN ISO 3744 : 1995-11 ; DIN EN ISO 11203 : 1996-07.
The noise level of the machine is measured according to standards DIN EN ISO 3744: 1995-11 and DIN EN ISO 11203: 1996-07. The values gi-
ven are emission values calculated according to applicable standards and not values relating to use in the workplace. Although correlation
between those different emission levels does exist, this cannot be reliably used to determine whether additional precautions are neces-
sary. Factors with potential influence on the sound emission level in the workplace include the length of the period of work, the size of the
room and any other sources of noise (e.g. number of machines operating, other noisy work being carried out at the same time). Accepta-
ble exposure levels may vary from one country to another. For all these reasons, we would advise users to wear equipment to protect their
ears while using this machine.
Acoustic pressure level LpA: 85.8 dB (A) Acoustic pressure level LwA: 96.8 dB (A)
Uncertainty: 3 dB (A)
Outlet with earth
earth
connection
Call in a qualified electrician or maintenance personnel if the earthing instructions are not fully understood or if in any doubt about the
correct earthing of the tool. If the power supply cable is damaged, it should be replaced by the manufacturer, the manufacturer's after-
sales department or similarly qualified person in order to avoid any danger. Do not use a tool if its power cord is damaged. This tool is
designed to be used with a circuit containing a power socket. It is also equipped with an earthing pin.

ENVIRONMENT PROTECTION

CONNECTING THE MACHINE – ELECTRICAL CONNECTIONS

NOISE INFORMATION

EARTHING INSTRUCTIONS

Earthing consists in connecting metal masses, that are liable to come accidentally
in contact with the current due to faulty insulation in an electrical device, to an
earth connection by means of a conductive wire. That earth connection, when used
with a differential circuit breaker, prevents electrical incidents. The current flows
directly into the earth and the power supply is automatically cut off. Do not modify
the supplied plug. If it cannot be put into the socket, have an appropriate socket
installed by a qualified electrician. If the earth conductor of a machine is incorrectly
connected, this can lead to a risk of electric shock. The earth conductor is contained
in green insulation with a yellow line. If the power cord needs to be repaired or
replaced, do not connect the earth conductor to a live terminal.
20