Publicité
Les langues disponibles
Les langues disponibles
Specifications and Safety
DESCRIPTION
This Submersible Sump Pump is designed for home
sumps. Unit is equipped with a 3-prong grounding-type
power cord. Shaded-pole motor is sealed for cooler
running. Sleeve bearings on motor shaft never need
lubrication. Automatic reset thermal protection. Not
designed for use as a swimming pool drainer.
SPECIFICATIONS
Power supply required ...........................115V, 60 HZ.
Liquid Temp. Range ................32°F to 70°F(0°-21°C)
Individual Branch Circuit Required (min.) ....15 Amps
Discharge.................................................1-1/2" FNPT
NOTICE: Do not reduce size of discharge pipe or
hose below 1-1/4" diameter. If discharge is too small,
pump will overheat and fail prematurely.
Pump water only with this pump.
NOTICE: This unit is not designed as a waterfall or foun-
tain pump, or for applications involving salt water or
brine! Use with waterfalls, fountains, salt water or brine
will void warranty.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.
PERFORMANCE
GPH (LPH) AT TOTAL FEET (M) OF LIFT
5
Model
HP
(1.5m)
CAPACITY GALLONS(L)/HOUR
3120
3996
1/3
(11,810) (8,631) (5,224)
3690
3994
1/2
(13,968) (11,356) (7,949)
3120
3886
1/3
(11,810) (8,631) (5,224)
3690
3884
1/2
(13,968) (11,356) (7,949)
ELECTRICAL & SWITCH SPECIFICATIONS
Individual
Branch
Circuit
Model
HP Req.(Amps)
3996
1/3
15
3994
1/2
15
3886
1/3
15
3884
1/2
15
For assistance, call Simer Customer Service at
10
15
20
(3m)
(4.6m)
(6m)
2280
1380
480
1,817
3000
2100
1140
4,315
2280
1380
480
1,817
3000
2100
1140
4,315
Switch Setting
in inches (mm)
On
Off
14.5"(368) 6.5"(165)
14.5"(368) 6.5"(165)
6.75"(171) 3.25"(83)
6.75"(171) 3.25"(83)
GENERAL SAFETY INFORMATION
Electrically powered sump pumps normally give
many years of trouble-free service when correctly
installed, maintained, and used. However, unusual
circumstances (interruption of power to the pump,
dirt/debris in the sump, flooding that exceeds the
pump's capacity, electrical or mechanical failure in
the pump, etc.) may prevent your pump from func-
tioning normally. To prevent possible water damage
due to flooding, consult your retailer about a sec-
ondary AC sump pump, a DC backup sump pump,
and/or a high water alarm. See the "Troubleshooting
Chart" in this manual for information about common
sump pump problems and remedies. For more infor-
mation, see your retailer, call Simer customer
service at 1-800-468-7867 / 1-800-546-7867.
1. Know the pump application, limitations, and
potential hazards.
2. Do not use in water with fish present. If any oil
leaks out of the motor it can kill fish.
3. Disconnect power before servicing.
4. Release all pressure within system before servic-
ing any component.
5. Drain all water from system before servicing.
6. Secure discharge line before starting pump. An
unsecured discharge line will whip, possibly
causing personal injury and/or property damage.
No flow
7. Check hoses for weak or worn condition before
at height
each use, making certain that all connections are
shown
below
secure.
22'
8. Periodically inspect sump, pump and system
(6.7m)
components. Keep free of debris and foreign
26'
objects. Perform routine maintenance as
(7.9m)
required.
22'
9. Provide means of pressure relief for pumps whose
(6.7m)
discharge line can be shut-off or obstructed.
26'
10. Personal Safety:
(7.9m)
a. Wear safety glasses at all times when working
with pumps.
b. Keep work area clean, uncluttered and prop-
erly lighted – replace all unused tools and
equipment.
c. Keep visitors at a safe distance from work
area.
d. Make workshop child-proof – with padlocks,
master switches, and by removing starter
keys.
11. When wiring an electrically driven pump, follow
all electrical and safety codes that apply.
12. This equipment is only for use on 115 volt (sin-
gle phase) and is equipped with an approved
3-conductor cord and 3-prong, grounding-type
plug.
1-800-468-7867 / 1-800-546-7867
2
Publicité
