Denon DJ X1850 PRIME Guide D'utilisation page 8

23. Stereo/Mono Selector: Use this switch to set the channel configuration of the master outputs:
Stereo (binaural audio using separate left and right channels) or Mono (summed monaural audio
through both left and right channels).
24. Pan: Turn this knob to adjust the position of the master outputs' signal in the stereo field.
25. Mic 1 Input: Use a standard XLR or 1/4" (6.35 mm) cable (not included) to connect a standard
dynamic microphone to this input. Use the Mic 1 Level knob on the top panel to control the
volume level.
26. Mic 1/2 Level: Turn these knobs to adjust the volume levels of the corresponding microphone
inputs. The light next to each knob indicates the current signal level by its color: green
(normal/optimal), orange (mid level) or red (maximum/peak).
27. Mic On/Off: Press these buttons to activate or deactivate the corresponding microphone.
28. Talk Over: Press this button to activate or deactivate the "talk over" feature, which automatically
reduces the volume level of the master mix when you speak into the microphone. You can use
the Utility menu to set how much the master mix volume level is lowered and how quickly it
returns to its normal level (see
29. Mic EQ (High, Low): Turn these knobs to boost or cut the high and low frequencies for both
microphones.
30. Headphone Outputs: Connect headphones to these 1/4" (6.35 mm) or 1/8" (3.5 mm) jacks for
monitoring the signal. Turn the Headphone Level knob to control the volume.
31. Headphone Level: Turn this knob to adjust the volume of the headphones.
32. Split Cue: When this switch is in the On position, the headphone audio will be "split" such that
all channels sent to cue channel are summed to mono and sent to the left headphone channel
and the master mix is summed to mono and sent to the right channel. When the switch is in the
Off position, the cue channel and master mix will be "blended" together.
33. Cue Mix: Turn this knob to adjust the balance between the cue output and the master mix
output in the headphones.
34. Displays: These displays provide instant feedback about effects parameters, tempo and more.
The displays also show the Utility menu, where you can configure hardware settings and change
feature behaviors to match your preferred workflow by adjusting audio signal routing, effects
module order, input and output levels, and more.
35. BPM FX On/Off: Press this button to turn the BPM effect module on or off.
36. FX Amount: Turn this knob to adjust the amount of output signal from the BPM effect module.
37. Instant: Press this button to enable or disable Instant FX Mode for the FX touch strip.
38. FX Channel Assign: Turn this knob to select the channel to which the BPM effect module will
apply its effects: Channel 1, 2, 3, or 4; X-Fader A or B (either side of the crossfader); Mic (both
microphone signals); or Master (the master mix).
39. FX Select/Enter: Turn this knob to select an effect. While in the Utility menu, turn this knob to
select an option, and press it to confirm your choice or enter a submenu.
40. Back: Press this button to return to the previous screen in the Utility menu.
41. FX Cue: Press this button to preview the BPM effects in the headphones' cue channel. Not all
BPM effects can be previewed, though.
42. FX Time/Parameter: Turn this knob to select the rate that the BPM effect module will use. Press
the knob to switch between adjusting the rate as a time division and the rate in milliseconds. (A
corresponding light along the FX touch strip will illuminate to indicate the current time division.)
This knob will also adjust other FX parameters when available.
43. FX Touch Strip: When the Instant button is off (disabled), tap an area of this touch-capacitive
strip to select the time division that the BPM effect module will use. A corresponding light along
the strip will illuminate to indicate the current time division. If the current time division is not a
quantization value shown on the strip (e.g., the BeatBreak effect), then none of the lights will
illuminate.
When the Instant button is on (enabled), tap and hold your finger on the strip to activate the
effects, and then drag your finger up or down to adjust the time division of the effect.
8
Operation > Utility Menu > Microphone).