Stanley D 200/8/6 Manuel Utilisateur page 16

G
B
1. PRECAUTIONS
An ACOUSTIC PRESSURE value of 4 m. corresponds
to the ACOUSTIC POWER value stated on the yellow
label located on the compressor, minus 20 dB.
THINGS TO DO
● The compressor must be used in a suitable
environment (well ventilated with an ambient
temperature of between +5°C and +40°C) and
never in places affected by dust, acids, vapors,
explosive or flammable gases.
● Always maintain a safety distance of at least 4 meters
between the compressor and the work area.
● Any coloring of the belt guards of the compressor
during painting operations indicates that the distance
is too short.
● Insert the plug of the electric cable in a socket of
suitable shape, voltage and frequency complying
with current regulations.
● Use extension cables with a maximum length of 5
meters and of suitable cross-section.
● The use of extension cables of different length and also
of adapters and multiple sockets should be avoided.
● Always use the switch I/O to switch off the
compressor.
● Always use the handle to move the compressor.
● When operating, the compressor must be placed on
a stable, horizontal surface.
NOT
THINGS
● Never direct the jet of air towards persons, animals
or your body. (Always wear safety goggles to protect
your eyes against flying objects that may be lifted by
the jet of air).
● Never direct the jet of liquids sprayed by tools connected
to the compressor towards the compressor.
● Never use the appliance with bare feet or wet hands
or feet.
● Never pull the power cable to disconnect the plug
from the socket or to move the compressor.
● Never leave the appliance exposed to adverse
weather conditions.
● Never transport the compressor with the receiver
under pressure.
● Do not weld or machine the receiver. In the case of
faults or rusting, replace the entire receiver.
● Never allow inexpert persons to use the compressor.
Keep children and animals at a distance from the
Preserve this handbook for future reference.
TO DO
work area.
● This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning the use of the appliance by
a person responsible for their safety.
● Children should be supervised to ensure that they do
not play with the appliance.
● Do not position flammable or nylon/fabric objects
closed to and/or on the compressor.
● Never clean the compressor with flammable liquids
or solvents. Check that you have unplugged the
compressor and clean with a damp cloth only.
● The compressor must be used only for air compression.
Do not use the compressor for any other type of gas.
● The compressed air produced by the compressor
cannot not be used for pharmaceutical, food or medical
purposes except after particular treatments and cannot
be used to fill the air bottles of scuba divers.
THINGS YOU SHOULD KNOW
● To avoid overheating of the electric motor, this
compressor is designed for intermittent operation
as indicated on the technical dataplate (for example,
S3-25 means 2.5 minutes ON, 7.5 minutes OFF). In the
case of overheating, the thermal cutout of the motor
trips, automatically cutting off the power when the
temperature is too high. The motor restarts automatically
when normal temperature conditions are restored.
● To facilitate restart of the compressor, in addition
to the operations indicated, it is important to
return the button of the pressure switch to the OFF
position and then to ON again (paragraph 5.4).
● The compressors are fitted with a pressure switch
equipped with a delayed closing air discharge valve
which facilitates start-up of the motor (D 200/8/6 - D
115/8/6 SIL only). Therefore venting of air from this valve
for a few seconds with the receiver empty is normal.
● All the compressors are fitted with a safety valve
that is tripped in the case of malfunctioning of the
pressure switch in order to assure machine safety.
● When fitting a tool, the flow of air in output must be
switched off.
● When using compressed air, you must know and comply
with the safety precautions to be adopted for each type
of application (inflation, pneumatic tools, painting,
washing with water-based detergents only, etc.).
16