Chicco Balloon Mode D'emploi page 13

9. K eep one clasp end blocked and simultaneously pull the belt
and slide it inside the relative ring (O), to adjust the tension of the
safety harness (Fig. 12).
BOOSTER CUSHION
10. T he reducer cushion (D) - (DD) is ideal from birth and can be
removed according to needs. To fix it to the seat, place it on the
seat and slide the crotch strap through the hole (Fig. 13). Thread
the safety harness in the relative side slots of the reducer cushion
(Fig. 13 A). Place the headrest (DD) to the desired height, it can
be chosen within three different heights; fix the headrest to the
seat, sliding the straps through the slot and close it again using
the velcro strap (Fig. 14).
TOYBAR
11. F asten the toybar (E) to the frame inserting the lower ends in the
relevant fastening hole of the toybar (Fig. 15).
WARNING: Always check that the toybar is properly fastened
before every use. The toybar can be used in two different modes,
slightly lifting it from its seat and turning it to the desired position
(Fig. 16).
12. T he toys can be fastened to the toybar inserting the belts in the
holes in the bar (Fig. 17).
WARNINGS ELECTRICAL PARTS
w-
• T o replace the batteries: loosen the screw on the battery compart-
ment cover with a screwdriver and open the cover. Then remove
en the spent batteries and fit new ones, paying attention that the
ake
poles are in the right direction (as shown on the product), close the
battery cover and tighten the screw. Repeat the same operation
he
for the Vibrating Box (Toybar 2 AA 1.5 Volt type batteries - Vibration
Box 1 LR20 1.5V battery).
• B atteries must only be fitted by an adult.
• O nly use alkaline batteries of the same type or equivalent to the
ed type recommended for the correct function of this product (Toy-
rd,
bar 2 AA 1.5V batteries - Vibration Box 1 LR20 1.5V battery).
hin • M ake sure the batteries are fitted with their poles in the right direction.
out
• Never mix new and old or different types of batteries.
be
• Always keep batteries and tools out of the reach of children.
• Do not short-circuit the power terminals.
ad-
• A lways remove discharged batteries from the product to avoid any
possible liquid leaks that may damage it.
on,
• A lways remove the batteries if the product will not be used for a
long period of time.
use. • R emove the batteries from the toybar and vibrating box before
disposing of the product.
ric. • D o not throw dead batteries in fire or leave them in the environ-
ed
ment; they must be disposed of through waste sorting.
• I f the batteries are leaking liquid, replace them immediately, mak-
ing sure to clean the battery compartment; thoroughly wash your
hands in the case of contact with the liquid.
• A lways dispose of leaking batteries immediately: they can cause
of
burns or other types of injuries.
• Do not try to recharge non-rechargeable batteries: they may explode.
so • T he use of rechargeable batteries is not recommended as they
may reduce the toy's operability.
• I f using rechargeable batteries, remove them from the toy before
recharging them.
• D o not leave the product outside under the rain; water infiltrations
hild
will damage the electronic circuit.
os- • R echargeable batteries must be charged only under adult supervision.
ont REMOVABLE SOUND TOY
The toybar is fitted with a sounds and lights panel that is activated
. 9)
by pressing the buttons on the front section (Fig. F).
F1 : On button - volume
F2 : It plays soothing and relaxing tunes
F3 : It plays lullabies
dy F4 : It plays funny music
F5 : Voice recording button
ove F6 : Sound and music activation handle
F7 : Microphone - Led
in For the voice recording activation, check that the sound toy is on.
ght Keep the F5 button pressed; as soon as the red LED flashes, the own
voice can be recorded, to stop recording release the button (the
LED will turn off ). The recording can have a maximum duration of
30 seconds.
To listen to the recording, press the button.
To record again, repeat the steps described above.
To obtain an optimal recording, it is recommended to keep a dis-
tance from the microphone (F7) of about 20 cm with a clear and
decisive tone of voice; it is important not to block the microphone
hole in order not to compromise the quality of your recording
The sound toy can be removed by pressing the button E1 (Fig. 18).
Once removed, the sound toy can be fastened to the bed frame
using the strap (I1) (Fig. 19). The strap has two slots to make it com-
patible to most of the bed frames (Fig. 20).
WARNING: To prevent possible injury by entanglement, remove
this toy when the child starts trying to get up on its hands and knees
in a crawling position
The fixing strap (I1), when not in use, can be fixed back to the trans-
port belt, as shown in Fig. 21
To refit the sound toy on the bar, slide it as indicated in Fig. 22 until
you hear it "CLICK" into place.
VIBRATION BOX
The vibration box (Fig. 23) is placed on the front seat support.
Turning the switch clockwise, the vibration starts, to turn it off, bring
the switch back to"0".
HOW TO REMOVE THE FABRIC COVER
It is possible to remove the seat cover and the booster cushion from the
reclined cradle to wash them.
13. Remove the booster cushion.
14. R emove the safety harness from the slots in the fabric and start
to remove the cover Fig.24. Release the 6 click buttons (Q) at the
side under the metal tubes, remove the cover on the vibrating box
(Fig. 25), then take off the fabric through the entire frame paying
attention not to damage it. To refit the cover, proceed in reverse
order, making sure that the lower fabric strap goes through the
adjustment joints of the backrest (Fig. 26) and the toybar support.
10/12 M, up to 18 Kg
(CHAIR USE)
• A ge range intended for use: from
when your child starts walking and
is able to sit down and stand up by
himself (about 10/12 months, max.
18 kg).
• WARNING: Before using as a chair,
remove the safety harness (crotch
strap and waist belt) and position
them in the relevant spaces.
• WARNING: Never leave the child
unattended.
• P lace only on flat and stable sur-
faces.
• D o not use the product as a chair in
rocker mode.
• T he dimensions of the product are
80 x 43 x 32/62.
• WARNING: Check that the space
13