Description Of Device / Spare Parts; Assembly; Start-Up - ATIKA RW 1800 Twin Notice Originale

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 17
D
e
s
c
r
i
p
t
i
o
n
o
f
D
e
s
c
r
i
p
t
i
o
n
o
f
Pos
Denomination
1.
Agitator
2.
Mortar beater - R
3.
Mortar beater - L
4.
Mortar beater (pair)
5.
ON / OFF-switch
6.
Trip switch
7.
Speed control
8.
2-speed switch
9.
Handle
10.
Holder - R
11.
Holder - L
12.
Sleeve - R
13.
Sleeve - L
14.
Safety label
Chucking the beaters
Risk of injury! Wear protective gloves.
The beater holders (10/11) and the beaters themselves
are identified by the letters R and L.
Push the sleeve (12/13) down and connect the beaters
(2/3) to the appropriately identified holders (10/11).
Make sure that the pin (a) is in the groove (b) on each
beater.
Release the sleeve. The beater is locked.
Check the safe seating of the beaters by pulling on
them.
S
S
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Check that the machine is completely and correctly assem-
bled.
Before each use, check
Connection cables for defects (cracks, cuts, etc.).
Do not use any defective cables.
there are no damages at the machine
(see "safe working")
that the beaters are properly secured.
14
d
e
v
i
c
e
/
S
p
a
r
e
p
a
r
t
s
d
e
v
i
c
e
/
S
p
a
r
e
p
a
r
t
s
Order-No.
RW 1800 Twin0
372673
372662
A
s
s
e
m
b
l
y
A
s
s
e
m
b
l
y
t
a
r
t
-
u
p
t
a
r
t
-
u
p
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to
the relevant and properly earthed plug.
Connect the machine via a 30 mA fault current safety
switch.
Do not use any defective connection cables.
Use connecting or extension cables up to a length of 1.5 m
featuring a core cross section of at least 25 mm².
Main fuse: 10 A
Switching on/off
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Switching on
Operate the trip switch (6) at first. Press the ON/OFF
button (5) on the handle.
Start the machine at the lowest rotational speed (Level
1).
Switching off
Release the ON/OFF handle button.
This machine is not suited for continuous operation.
Speed control
With this type, the motor's speed and thus the agitator perfor-
mance can be adjusted. (Level 1 - 6).
You can continuously adjust the speed with the speed
control (7).
Level 1
Min. power = SLOW.
Level 6
max. power = FAST.
2- speed gear
The device is equipped with a 2-speed gear.
For the speed selection turn the switch (8) by 180°.
1. speed: 0 min
bis 450 min
–1
2. speed: 0 min
bis 790 min
-1
Only operate this switch at standstill.
–1
-1

Publicité

Table des Matières
loading

Table des Matières