Safe Working - ATIKA RW 1800 Twin Notice Originale

S a f e w
S a f e w
Pass the safety instructions on to all persons who work
with the machine.
Keep these safety instructions in a safe place.
Follow the attached "General safety instructions".
Do not use the machine for unsuitable purposes (see "Nor-
mal intended use" and "Working with the agitator").
Do not touch, inhal (dust) or swallow cement and
additives. Wear personal protective equipment (gloves,
safety goggles, face mask) when filling or emptying the mix-
ing container.
Keep children, bystanders and animals at a distance from
your working area. Do not allow other persons, especially
children, to touch the tool or the cable.
Switch off the machine if persons, in particular children or
pets, are close to you or if you change your working area.
The operator is resposnible to third persons within the area
of operations.
The operator is responsible for accidents or risks which
occur to other persons or their properties.
Never operate the machine if other persons are in the im-
mediate vicinity.
Children and young persons under 16 years of age as well
as persons who have not read the instruction manual are
not allowed to operate this product.
Never leave the device unattended.
Only operate the machine with complete and correctly at-
tached safety equipment and do not alter anything on the
machine that could impair the safety.
Do not modify the device or parts of the device respectively.
Switch the machine off and remove the mains
plug from the socket when
carrying out repair works
−
maintenance and cleaning
−
eliminating faults.
−
checking connecting lines, whether these
−
are knotted or damaged.
transport
−
leaving unattended (even during short interruptions).
−
unusual noises and vibrations
−
Thoroughly maintain your agitator:
Make sure that the ventilation apertures are free.
−
Keep handles dry and free of oils and grease. Follow the
−
maintenance instructions.
Check the machine for possible damage:
Before further use of the machine the safety devices
−
must be checked carefully for their proper and intended
function.
Check whether movable parts function perfectly and do
−
not stick or whether parts are damaged. All parts must
be correctly installed and fulfil all conditions to ensure
perfect operation of the machine.
Damaged guards and parts must be properly repaired or
−
exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
Damaged or illegible safety labels should be replaced
−
immediately.
o r k i n g
o r k i n g
Store unused equipment in a dry, locked place out of the
reach of children.
Electrical Safety
Design of the connection cable according to IEC 60 245 (H
07 RN-F) with a core cross-section of at least
⇒ 3 x 1.5 mm² for a maximum cable length of up to 25 m
⇒ 3 x 2.5 mm² for cable lengths over 25m
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic mate-
rial of same mechanical stability or be covered with this ma-
terial.
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Wind off completely the cable when using a cable drum.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service points.
Use only original spare parts. Accidents can arise for the
user through the use of other spare parts. The manufac-
turer is not liable for any damage or injury resulting from
such action.
13