Publicité
Les langues disponibles
Les langues disponibles
TECHNICAL DATA
CORDLESS PERCUSSION DRILL/DRIVER
Production code...............................................................................................
Drilling capacity in steel ...................................................................................
Drilling capacity in wood (with hole saw bit) .....................................................................
Drilling capacity in brick and tile ......................................................................
Wood screws (without pre-drilling) ..................................................................
No-load speed 1st gear ...................................................................................
No-load speed 2nd gear ..................................................................................
Impact rate 1st gear.........................................................................................
Impact rate 2nd gear .......................................................................................
Torque with battery (4.0 Ah) *1 ........................................................................
Torque with battery (6.0 Ah) *1 ........................................................................
Battery voltage.................................................................................................
Drill chuck range ..............................................................................................
Weight according EPTA-Procedure 01/2014 (1.5 Ah / 2.0 Ah) ........................
Weight according EPTA-Procedure 01/2014 (3.0 Ah / 4.0 Ah) ........................
Recommended ambient operating temperature ..............................................
Recommended battery types...........................................................................
Recommended charger ...................................................................................
Noise/vibration information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ................................................
Sound power level (Uncertainty K=3dB(A)) .....................................................
Always wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to
EN 60745.
Vibration emission value a
h
Percussion drilling into concrete a
...........................................................
h,ID
Uncertainty K= .............................................................................................
Drilling into metal a
...................................................................................
h,D
Uncertainty K= .............................................................................................
Screwing a
..................................................................................................
h
Uncertainty K= .............................................................................................
*1 Measured according to AEG standard N 877318
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent
accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually
doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the hands warm,
organisation of work patterns.
WARNING Read all safety warnings, instructions, illustrations
and specifi cations provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fi re and/or serious
injury. Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Wear ear protectors when impact drilling. Exposure to noise can cause
hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can
cause personal injury.
Brace the tool properly before use. This tool produces a high output
torque and without properly bracing the tool during operation, loss of
control may occur resulting in personal injury.
Hold the power tool by insulated gripping surfaces, when performing
an operation where the cutting accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an electric shock.
Never operate at higher speed than the maximum speed rated of the
drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely
without contacting the workpiece, resulting the personal injury.
Always start drilling at low speed and with the bit tip in contact with
the workpiece. At higher speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece, resulting the personal injury.
Apply pressure only in direct line with the bit and do not apply
excessive pressure. Bits can bend causing breakage or loss of control,
resulting in personal injury.
SCREWDRIVER SAFETY WARNINGS
Hold the power the tool by insulated gripping surfaces, when
performing an operation where the fastener may contact hidden
wiring. Fasteners contacting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an electric shock.
20
ENGLISH
BSB18BL
...................................4693 92 01...
...000001-999999
........................................ 13 mm
...................................... 100 mm
........................................ 20 mm
........................................ 15 mm
................................... 0-550 min
-1
................................. 0-2000 min
-1
................................. 0-8800 min
-1
............................... 0-32000 min
-1
...................................... 100 Nm
...................................... 140 Nm
........................................ 18 V
.................................. 1,5-13 mm
....................................... 2.1 kg
....................................... 2,4 kg
................................... -18...+50 °C
.................L1840R, L1830R, L1820R, L1815R
.......................................BL1218
..................................... 94,5 dB (A)
................................... 105,5 dB (A)
..................................... 10,9 m/s
2
....................................... 1,5 m/s
2
.................................... < 2,5 m/s
2
....................................... 1,5 m/s
2
.................................... < 2,5 m/s
2
....................................... 1,5 m/s
2
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with
the machine. The use of protective clothing is recommended, such as dust
mask, protective gloves, sturdy non-slip footwear, helmet and ear
defenders.
The dust produced when using this tool may be harmful to health. Do not
inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch
the device on again while the insertion tool is stalled, as doing so could
trigger a sudden recoil with a high reactive force. Determine why the
insertion tool stalled and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables
and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can
cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning
them. AEG Distributors off er to retrieve old batteries to protect our
environment.
Do not store the battery pack together with metal objects (short circuit risk).
Use only System GBS chargers for charging System GBS battery packs.
Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms.
Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it off
immediately with soap and water. In case of eye contact rinse thoroughly
for at least 10 minutes and immediately seek medical attention.
ALWAYS USE A SIDE HANDLE when using a 9.0 Ah or higher capacity
battery pack; the output torque of some tools may increase. If your drill/
driver did not come with a side handle, use the spare part side handle (see
explosion drawing of the tool).
Do not insert the bit on tool when the tool is running, and switch is lock on
status, the bit will be run and may hurt the user
Warning! To reduce the risk of fi re, personal injury, and product damage
due to a short circuit, never immerse your tool, battery pack or charger in
fl uid or al-low a fl uid to fl ow inside them. Corrosive or conductive fl uids,
such as seawater, certain industrial chemicals, and bleach or bleach
containing products, etc., Can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The electronic battery percussion drill/screwdriver may be used for drilling,
percussion drilling, as well as screwdriving for independent use away from
mains supply.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described under
"Technical Data" fulfi lls all the relevant provisions of the directives 2011/65/
EU (RoHS), 2014/30/EU, 2006/42/EC and the following harmonized
standards have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-1:2010
EN 60745-2-2:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015
EN 50581:2012
Winnenden, 2018-05-31
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the
battery pack. Avoid extended exposure to heat or sunshine (risk of
overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be fully
charged.
To obtain the longest possible battery life remove the battery pack from the
charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from
moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that
cause high current draw, the tool will vibrate for about 2 seconds and then
the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the battery could
become to high. If this happens, the battery will shut down.
Place the battery on the charger to charge and reset it.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to
Dangerous Goods regulations. Transport preparation and transport are
exclusively to be carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
Use only AEG accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our AEG
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
machine type printed as well as the six-digit No. on the label and order the
drawing at your local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Please read the instructions carefully before
starting the machine.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached the
end of their life must be collected separately and
returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
n
No-load speed
0
V
Volts
Direct current
European Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH
21
Publicité
