Roadstar CLR-2496P Manuel D'instructions page 4

the battery is exhausted. The time and alarm settings will be lost. When power
is restored the clock will begin to flash indicating that the time and alarm set-
tings must be corrected.
DISPLAY
1. Normally the LCD DISPLAY indicates the DATE, which shows the MONTH,
YEAR, TIME and DAY.
2. Press SOOZE / LIGHT button (13) to increase the brightness of the LCD
display.
SETTING THE LCD DISPLAY
1. In the normal Display mode, to set the TIME, keep pressed SET (3) Button
until the 24H digits will flash. Press SCAN + / - (4-9) to adjust the 12/24 di-
gits.
2. To set the TIME, press SET (3) once more and the HOUR digits will flash.
Press SCAN + / - (4-9) to adjust the HOUR digits.
3. To set the MINUTE, press SET (3) once more and the MINUTE (3) digits
will flash. Press SCAN + / - (4-9) to adjust the MINUTE digits.
4. To set the YEAR, press SET (3) once more and the Year digits will flash.
Press SCAN + / - (4-9) to adjust the YEAR.
5. To set the MONTH, press SET (3) again and the MONTH digits will flash.
Press SCAN + / - (4-9) adjust the MONTH digit.
6. To set the DAY, press SET (3) again one more and the DAY digit will flash.
Press SCAN + / - (4-9) to adjust the DAY digit.
7. Press the SET (3) button to conclude the setting.
SETTING THE ALARM (BUZZER OR RADIO)
1. In the normal Display mode, press ALARM 1 (7) or ALARM 2 (8) button on-
ce and the display will show the ALARM TIME. The "AL" icon indicates that
the display is showing the ALARM TIME.
2. To set the ALARM TIME, press ALARM 1 (7) or ALARM 2 (8) button for 4
seconds and the OUR digits will flash. Press SCAN + / - (4-9) to adjust the
HOUR digits.
English 3 4 English
3. To set the ALARM MINUTE, press ALARM 1 (7) or ALARM 2 (8) button
once more and the MINUTE digits will flash. Press SCAN + / - to adjust the
MINUTE digits.
4. To set the BUZZER or RADIO Alarm Mode, press ALARM 1 (7) or ALARM
2 (8) button sequentially to select betwen BI (Buzzer) RAD (Radio) or OFF
mode.
5. To disable the Alarm mode, during normal display mode keep press se-
quentially the Alarm 1 (7) or Alarm 2 (8) buttons seconds until OFF compare
in the display.
DIMMER FUNCTION
Press quickly the SNOOZE/LIGHT (2) button to change the Display intensity.
LED BACKLIGHT
When it is not in the wake up time, the SNOOZE/LIGTH button is for tuning on
the LCB Backlight & Time Projector.
1. Press once for the light ON for 60 seconds.
2. Press and Hold for the lights always ON. LCD backlight will flash once for
indication. Press & hold again until the LCD flash once then release to disa-
bling this function.
FM PLL RADIO
1. Make sure the antenna wire (10 is completely unrolled and extended.
2. In normal clock mode, press the MODE button (1) to switch on the radio.
3. Press the SCAN + / - (4-9) button to search for the station. Short press mo-
de is MANUAL research, press and hold that the search mode is automatic.
4. To save the channel, press the MEMO (3 ) 5 seconds toenter the memory
of the radio station , then press SCAN + / - (4-9) to select the desired chan-
nel number where you want to save the station.
5. After selecting the desired channel , press the MEMO button (3) to confirm
the location of the memory.
6. To recall radio stations , press the MEMO button (3) sequentially until the
desired channel is displayed.