Publicité
Les langues disponibles
Les langues disponibles
OPERATING INSTRUCTIONS
Filling your Canister Steam Cleaner
with Water
IMPORTANT:
Always insure that the
unit is "UNPLUGGED" from the wall
receptacle and all switches are in the "Off"
position prior to initial filling or re-filling the
water tank. Never attempt to fill this unit
under a water tap, always use the filling
flask and funnel provided. Failure to
follow these steps will cause the water
tank to overfill and may pose an electrical
safety hazard.
RECOMMENDATION
: The use of
distilled/demineralized water is
recommended, particularly in areas with
hard water in order to prevent the build-up
of lime scale.
Step 1: Press the safety cap down and
turn counter clockwise until
removed.
Step 2: Assure that the steam cleaner is
empty so that the addition of the
prescribed amount of water will
not result in overfilling.
Step 3: Add 47 fl. oz (1400 ml) of water
using the filling flask and funnel
provided. (Fig. 1) Do not
overfill. Replace safety cap by
turning clockwise - press down
firmly to tighten. Heating time is
approximately 8-10 minutes.
Filling the boiler with hot water
will shorten heat up time.
Step 4: Connect the desired accessory
onto the steam hose.
Step 5: Plug the unit into a standard
120 volt wall receptacle. Press
the On/Off switch. The Heating
light (Red) will light up.
Step 6: Allow approximately 8-10
minutes for water vapor to reach
its working temperature. When
the unit is ready for use the
steam ready light will light up.
Step 7: Upon initial use, some water
will come out from the hose
nozzle. This is residual water
that is left over in the hose from
the last use and is normal.
CAUTION: Always point the
nozzle outlet in a safe
direction. Never point in the direction of
yourself, other people or pets.
Fig. 1
NOTE:
When the steam cleaner has
run out of water, steam output will
cease.
Refilling Unit With Water
WARNING: Always allow
the unit to cool for 15
minutes before re-filling. When re-
filling the steam cleaner while it is
still hot, the first drops of water
might bubble up. Use caution when
opening the safety cap as cap may
become hot during use and
escaping steam can cause
scalding.
Step 1: Press the On/Off button on
the unit to the "Off" position.
Step 2: Press the On/Off steam
switch to the "On" position
and wait until no more steam
comes out of the hose.
Step 3: Remove the plug from the
electrical outlet and allow the
unit to cool for approximately
15 minutes before refilling
with water.
Step 4: After completing the cool
down period of step 3
(above), carefully press down
on the safety cap and turn
counter clockwise to loosen.
5
OPERATING INSTRUCTIONS
Step 5: Slowly pour water using the
filling flask and funnel provided
into the boiler. DO NOT Fill
Under a faucet. Always use the
filling flask and funnel that are
provided. DO NOT OVERFILL.
Never put more than 47 ounces
(1400 ml) of water in the unit at
one time.
Step 6: Screw safety cap back on to the
unit by turning clockwise and
press down to tighten securely.
Plug appliance back into wall
outlet. Steam will start to be
produced as before.
Using Your Steam Cleaner with
Steam Pocket
Step 1: Connect one of the extension
tubes to the hand grip on the
flexible steam hose. To
attach the extension tubes
one onto the other or onto the
hand grip, press the locking
button ensuring that it fits into
the hole. (Fig. 2) To
disconnect, repeat the
operation by pressing the
locking button and pulling the
two sections apart.
Fig. 2
NOTE:
Fit the steam pocket frame with
the angle adapter onto the
extension tube.
Step 2: If the angle adapter is not
attached to the steam pocket
frame, attach as follows: Hold
the steam pocket
frame in one hand
and the angle
adapter in the
other. Insert the
angle adapter
Fig. 3
stem into the
opening of the steam pocket
frame as shown in Fig. 3.
Note that the flat on the nozzle
must face toward the side of
the frame with the brass pin.
Once inserted, rotate it 90°.
Attaching the Steam Pocket
Towel to the Frame
WARNING:
Always insure the
unit is "UNPLUGGED" from the
wall receptacle prior to attaching or
removing accessories.
1. Slide the steam pocket towel over the
steam pocket frame. (Fig. 4)
Fig. 4
2. Bring the towel all the way to the
top of the steam pocket frame.
(Fig. 5)
Fig. 5
3. Bring the velcro strips that are on the
back side of the steam pocket towel
over the steam pocket frame and
attach to the inside of the front side of
the steam pocket towel. (Fig. 6)
Fig. 6
6
Publicité
