ADEO SCREEN BIFORMAT Manuel D'installation page 10

ENGLISH – Motorized screen user manual
WARNING - - - - READ CAREFULLY BEFORE PERFORMING ADJUSTMENTS WARNING WARNING WARNING READ CAREFULLY BEFORE PERFORMING ADJUSTMENTS READ CAREFULLY BEFORE PERFORMING ADJUSTMENTS READ CAREFULLY BEFORE PERFORMING ADJUSTMENTS
Adjustments shown on Fig. 5 must be performed by authorised and specialised personnel only. Incorrect performance of the procedures described may result in damages to the
product which will not be covered by guarantee. End stops adjustment varies depending on the surface position (first surface is front and second surface is rear)ft side) or on drop of
the curtain (front or rear); the diagram on Fig. 5 is sectioned based on these variants. Adjustment is performed with a 4 mm hex wrench (included).
END STOPS ADJUSTMENT SCREWS ARE POSITIONED IN THE BOTTOM AND FRONT PART OF THE SCREEN, AND NOT IN THE RIGHT OR LEFT HAND SIDES. DO NOT ADJUST THE END
STOPS WHEN UP OR DOWN BUTTON IS ACTIVATED.
WARNING WARNING WARNING WARNING
End stop is adjusted so as to allow the projection sheet to wind around the roller at least 1.5 times to avoid the sheet coming loose. Special attention must be paid when end stops are adjusted in such a
way that projection sheet unwinds beyond the factory setting. This is allowed within a limit of 3 cm without posing a risk to the product. Incorrect adjustment of end stops can cause:
-Projection sheet coming away from the roller
-Projection sheet winding the wrong way, with ensuing damage to flatness of the projection surface and to winding mechanisms
-Breaking of bottom end black frame welding (framed screens)
-Excessive strain on motor with possible ensuing damage and activation of motor's thermal resistance
-Excessive winding of the end stop adjustment system with ensuing breaking of the mechanical part
GUARANTEE GUARANTEE
GUARANTEE GUARANTEE
Operators are reminded that in cases where seals have been tampered with and where any damages have resulted from incorrect adjustment, repair interventions shall not be covered by guarant
PROGRAMMING END STOPS MOTOR NICE 230V 50Hz/NICE 120V 60Hz PROGRAMMING END STOPS PROGRAMMING END STOPS PROGRAMMING END STOPS MOTOR NICE 230V 50Hz/NICE 120V 60Hz MOTOR NICE 230V 50Hz/NICE 120V 60Hz MOTOR NICE 230V 50Hz/NICE 120V 60Hz ( ( ( ( procedures already carried out in factory
FIG 5
FRONT SIDE SURFACE
PROGRAMMING END STOPS MOTOR PROGRAMMING END STOPS MOTOR SOMFY RTS
PROGRAMMING END STOPS PROGRAMMING END STOPS MOTOR MOTOR
Move the
screen surface
to down limit
switch.
Move the
screen surface
to up limit
switch.
Made by Adeo Screen sp. Z o.o. (Polska) Specifications are subject to change without notice. E&OE
Doc: BIFORMAT Installation Manual rev5 | 29.01.2015
Please verify that you are working with the latest revision of this document before specifying your screen.
10 10 10 10 END STOP MOTOR ADJUSTMENT
SOMFY RTS 230V 50Hz/120V 60Hz 230V 50Hz/120V 60Hz ( ( ( ( procedures already carried out in factory
SOMFY RTS SOMFY RTS 230V 50Hz/120V 60Hz 230V 50Hz/120V 60Hz
1 Press both
and
same time until you will see
a brief up and down motion
of screen surface.
1. Press both
and
same time until you will see
a brief up and down motion
of screen surface.
END STOP MOTOR ADJUSTMENT
END STOP MOTOR ADJUSTMENT END STOP MOTOR ADJUSTMENT
procedures already carried out in factory, , , , SHOULD NOT be performed by unauthorised personnel procedures already carried out in factory procedures already carried out in factory
REAR SIDE SURFACE
procedures already carried out in factory, , , , SHOULD NOT be performed by unauthorised personnel
procedures already carried out in factory procedures already carried out in factory
Down limit swi Down limit swi Down limit swi Down limit swit t t t ch ch ch ch
2
Move the screen with
at the
to reach the desired
down limit position.
Up limit swicht Up limit swicht Up limit swicht Up limit swicht
2
Move the screen with
at the
to reach the desired up
SHOULD NOT be performed by unauthorised personnel) ) ) ) SHOULD NOT be performed by unauthorised personnel SHOULD NOT be performed by unauthorised personnel
SHOULD NOT be performed by unauthorised personnel) ) ) )
SHOULD NOT be performed by unauthorised personnel SHOULD NOT be performed by unauthorised personnel
3
4
buttons
Press button until you
will see a brief up and down
and
motion of screen surface to
memorize the new position
3
4
buttons
Press button until you
will see a brief up and down
and
motion of screen surface to
memorize the new position
limit position.
Page 10