Table des Matières
Publicité
Level Plus
RefineME
®
®
Manuel d'utilisation
13.2 Certificats
4.5 POINT TEXT SIZE
Des versions téléchargeables de tous les certificats sont disponibles
sur www.mtssensors.com, depuis la page d'accueil de chaque produit.
En cas de difficulté à obtenir les certificats sur le Web, contacter le
Support technique MTS : une copie électronique vous sera envoyée.
13.3 NEC (FM)
MTS TO PRINT
13.3.1 Sécurité intrinsèque
MODEL NO.
13.3.1.1 Conditions d'utilisation spéciales
SERIAL NO.
1. Le boîtier de l'appareil contient de l'aluminium et peut constituer
DATE CODE.
un risque potentiel d'inflammation par impact ou friction. Prendre
toutes les précautions pendant l'installation et l'utilisation pour
éviter les risques d'impact ou de friction. (En cas d'installation
dans le cadre d'une Approbation GA)
2. La température ambiante maximale autorisée du transmetteur
de niveau numérique/analogique Level Plus est de 71 °C. Pour
USE FM LOGO ARTWORK
éviter les effets de la température du processus et d'autres effets
thermiques, s'assurer que la température ambiante autour et dans
le boîtier du transmetteur ne dépasse pas 71 °C.
4.5 POINT TEXT SIZE
3. Certains modèles contiennent des pièces du boîtier de
fabrication autre que métallique, pour éviter le risque d'étincelle
électrostatique, la surface non-métallique ne doit être nettoyée
ENTITY PARAMETERS:
qu'avec un tissu humide.
8 POINT TEXT
SEE PRINT REFERENCE CHART
B
13.3.1.2 Étiquettes
SERIAL NO./DATE CODE
MTS Systems Corporation
Sensors Division
3001 Sheldon Dr.
Cary, NC 27513
NOTES:
1. STANDARD LETTERING UNIVERS 55
OR ITC GARAMOND BOOK.
Model No:
B
2. MATERIAL TO BE SCREEN PRINTED ALUMINUM WITH SATIN
Serial No:
BACKGROUND AND BLACK TEXT OR LASER ETCHED ALUMINUM.
SERIAL NO./DATE CODE
∆
3.
INDICATES CRITICAL DIMENSIONS.
Date :
4. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES.
5. MATERIAL: .8 [0.03] THICK ALUMINUM
6. REFER TO TABLE 1 FOR "L1" & "L2" DIMENSIONS.
APPROVED
NOTES:
1. STANDARD LETTERING UNIVERS 55
OR ITC GARAMOND BOOK.
WARNING: REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS
2. MATERIAL TO BE SCREEN PRINTED ALUMINUM WITH SATIN
A
BACKGROUND AND BLACK TEXT OR LASER ETCHED ALUMINUM.
∆
3.
INDICATES CRITICAL DIMENSIONS.
4. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES
Fig. 15 : Étiquette FM sécurité intrinsèque, Modbus ou DDA, boîtier NEMA
69.85 [2.75]
5. MATERIAL: .8 [.03] THICK ALUMINUM
6. REFER TO TABLE 1 FOR "L1" & "L2" DIMENSIONS.
2
USE MTS LOGO
ARTWORK
10 POINT SIZE
MTS TO PRINT
MODEL NO.
SIZE
Level Plus Transmitter
®
***NO REVISIONS SHALL BE MADE WITHOUT THE
3.47 [.14]
8.97 [.35]
B
A
MTS TO PRINT
REV
MODEL NO.
PROPRIETARY DATA
THE INFORMATION AND DESIGN(S) DISCLOSED
HEREIN ARE THE PROPERTY OF MTS SYSTEMS
INTRINSICALLY SAFE
CORPORATION AND MAY NOT BE USED,
FM
US
CL. I, Div. 1, GR. ABCD
REPRODUCED OR DISCLOSED IN ANY FORM
***NO REVISIONS SHALL BE MADE WITHOUT THE NOTIFICATION
3.47 [.1
CL. I, Zone 0/1, AEx ia IIC T4
8.97 [.35]
EXCEPT AS GRANTED IN WRITING BY MTS
Ta = -50°C to +71°C
IP65
;
C
SYSTEMS CORPORATION. THIS RESTRICTION
when connected in accordance
installa on
with FM approved
EXCLUDES INFORMATION THAT IS IN THE
B
drawing # 651543-1
PUBLIC DOMAIN OR WAS LEGITIMATELY IN THE
A
PRIOR POSSESSION OF THE RECIPIENT.
R
E
V
P/N 551629-1 Rev B
2
PROPRIETARY DATA
THE INFORMATION AND DESIGN(S) DISCLOSED
HEREIN ARE THE PROPERTY OF MTS SYSTEMS
CORPORATION AND MAY NOT BE USED,
REPRODUCED OR DISCLOSED IN ANY FORM
EXCEPT AS GRANTED IN WRITING BY MTS
***NO REVISIONS SHALL BE MADE WITHOUT THE NOTIFICATION
SYSTEMS CORPORATION. THIS RESTRICTION
MTS Systems Corporation
Sensors Division
3001 Sheldon Dr.
Cary, NC 27513
Model No:
Serial No:
Date :
2
WARNING: REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS
Fig. 16 : Étiquette FM sécurité intrinsèque, HART
R3.30 [.13]
2
R
MTS Systems Corporation
Sensors Division
3001 Sheldon Drive, Cary, N.C. 27513
28.70 [1.13]
INTRINSICALLY SAFE
CL. I, Div. 1, GR. ABCD
CL. I, Zone 0/1, AEx ia IIC T4
7847
1.78 [.07]
Ta = -50°C TO +71°C ; IP65
IP RATING WAS 66
WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY
REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS
7570
RELEASE TO PRODUCTION
Fig. 17 : Étiquette FM sécurité intrinsèque, Modbus ou DDA, boîtier à cavité simple ou double
ECO #
15.80 [.62]
R
MTS Systems Corporation
Sensors Division
3001 Sheldon Drive, Cary, N.C. 27513
INTRINSICALLY SAFE
CL. I, Div. 1, GR. ABCD
CL. I, Zone 0/1, AEx ia IIC T4
Ta = -50°C TO +71°C ; IP65
8256
WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY
34.69 [1.37]
REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS
7
8
4
7
Fig. 18 : Étiquette FM sécurité intrinsèque, HART
7570
1.78 [.07]
E
C
O
#
I
22
I
8 POINT TEXT
SIZE
Level Plus Transmitter
INTRINSICALLY SAFE
FM
US
CL. I, Div. 1, GR. ABCD
APPROVED
CL. I, Zone 0/1, AEx ia IIC T4
Ta = -50°C to +71°C
when connected in accordance
"L1"
with FM approved
drawing # 651543-1
651544-1
∆ "L2"
USE MTS LOGO ARTWORK
14.0 POINT SIZE
, boîtier NEMA
®
69.85 [2.75]
7.5 POINT SIZE
Level Plus Transmitter
"L1"
∆
"L2"
USE MTS LOGO ARTWORK
14.0 POINT SIZE
7.5 POINT SIZE
DESCRIPTION
Level Plus Transmitter
UNLESS OTHERWISE SPECIFIED
0 PLACES
MM
86.30 [3.40]
0.5
ADDED "D1"
- THREAD DEPTHS ARE TO MIN. FULL THDS
- DRILL DEPTHS ARE TO FULL DIA.
P I
R
A
T
N I
- REMOVE BURRS AND SHARP EDGES
, boîtier à cavité simple ou double
®
- DO NOT SCALE PRINT
RELEASE FOR PRODUCTION
NOTES:
- MACHINED SURFACE FINISH 3.2uM [125 uIn
D
E
S
C
R
1. STANDARD LETTERIN
UNLESS OTHERWISE SPECIFIED
TOLERANCES
2. DIMENSIONS IN BRAC
0 PLACES
1 PLACE
MM
MM
0.5
0.1
3. MATERIAL: 3M 7883 M
- THREAD DEPTHS ARE TO MIN. FULL THDS
®
1.78 [.07
IP65
DASH
;
#
installa on
-1
1.78 [.0
-2
551641-1
P/N 551629-1 Rev B
1
17.53 [.69
FM
APPROVED
INSTALL PER DRAWING # 651543-1
SUPPLY VOLTAGE: 28 VDC
P/N 551634-X Rev C
SEE TAB
4.0 POINT TEX
(TYP.)
TOLERANCES
17.53 [.69
FM
1 PLACE
APPROVED
ANGLES
MM
0.1
INSTALL PER DRAWING # 651544-1
SUPPLY VOLTAGE: 28 VDC
P/N 551642-X Rev C
G
W
A
S
6
6
SEE TAB
4.0 POINT TEXT SIZE
P I
I T
O
N
(TYP.)
TITLE
OR ITC GARAMOND B
(ACP) LA
ANGLES
m
IN INCHES.
FIRST
ANGLE
R3.3
28.
15
H
34.
LI
FM LOG
4.5 PO
"D1"
FM L
4.5 P
"D1"
S
Publicité
Table des Matières
