Makita XRU09 Manuel D'instruction page 4

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

3.
Check damaged parts before further use of the
tool. A guard or other part that is damaged should
be carefully checked to determine that it will
operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other condition that may affect
its operation. A guard or other part that is
damaged should be properly repaired or replaced
by our authorized service center unless indicated
elsewhere in this manual.
4.
Switch on the motor only when hands and feet
are away from the nylon cutting head.
5.
Before starting make sure that the nylon cutting
head has no contact with hard objects such as
branches, stones etc. as the nylon cutting head
will revolve when starting.
6.
Remove any adjusting key, wrench or blade cover
before turning the power tool on. An accessory
left attached to a rotating part of the power tool
may result in personal injury.
Method of operation
1.
Only use the tool in good light and visibility.
During the winter season beware of slippery or
wet areas, ice and snow (risk of slipping). Always
ensure a safe footing.
2.
Take care against injury to feet and hands from
the nylon cutting head.
3.
Never cut above waist height.
4.
Never stand on a ladder and run the tool.
5.
Never climb up into trees to perform cutting
operation with the tool.
6.
Never work on unstable surfaces.
7.
Remove sand, stones, nails etc. found within the
working range. Foreign particles may damage the
nylon cutting head.
8.
Should the nylon cutting head hit stones or other
hard objects, immediately switch off the motor
and inspect the nylon cutting head.
9.
Before commencing cutting, the nylon cutting
head must have reached full working speed.
10. During operation always hold the tool with both
hands. Never hold the tool with one hand during
use. Always ensure a safe footing.
11.
The nylon cutting head has to be equipped with
the guard. Never run the tool with damaged
guards or without guards in place!
12. All protective equipment such as guards supplied
with the string trimmer must be used during
operation.
13. Except in case of emergency, never drop or cast
the tool to the ground or this may severely
damage the tool.
14. Never drag the tool on the ground when moving
from place to place, the tool may become
damaged if moved in this manner.
15. Always remove the battery cartridge from the tool:
whenever leaving the tool unattended;
before clearing a blockage;
before checking, cleaning or working on the
tool;
whenever
abnormally;
whenever transporting the tool.
16. Always ensure that the ventilation openings are
kept clear of debris.
17. Hold the power tool by insulated gripping
surfaces only, because the cutter blade may
contact hidden wiring. Cutter blades contacting a
"live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
Maintenance instructions
1.
The condition of the nylon cutting head, protective
devices must be checked before commencing
work.
2.
Turn off the motor and remove the battery
cartridge
before
replacing the nylon cutting head or nylon cord
and cleaning the tool.
3.
Check for loose fasteners and damaged parts
such as cracks in the nylon cutting head.
4.
Follow instructions for lubricating and changing
accessories if applicable.
5.
When not in use store the equipment in an indoor
dry location that is locked up or out of children's
reach.
6.
Use only the manufacturer's recommended
replacement parts and accessories.
7.
Inspect and maintain the tool regularly, especially
before/after use. Have the tool repaired only by
our authorized service center.
8.
Keep handles dry, clean and free from oil and
grease.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
SAVE THESE INSTRUCTIONS.
4
the
tool
starts
carrying
out
maintenance,
vibrating

Publicité

Table des Matières
loading

Table des Matières