General Storage Guidelines; General Maintenance; Engine Specifications And Capacities - DeWalt DXGN Série Guide D'utilisation

GENERAL STORAGE GUIDELINES

GASOLINE FUEL FUMES ARE
FLAMMABLE. DO NOT STORE YOUR GENSET IN ANY
AREA THAT IS INDOOR OR IN POORLY VENTILATED
AREAS. GASOLINE FUEL FUMES CAN IGNITE IN THE
PRESENCE OF ANY OPEN FLAME, PILOT LIGHT, CLOTHES
DRYER, WATER HEATER, ETC.
Your generator should be started and operated for
several minutes at least every 30 days. When the generator
set is not being operated or is being stored more than one
month, follow these instructions:
1. Replenish engine oil to upper level.
2. Run the generator, then close the fuel shut-off valve and
allow the unit to run until the engine stops.
3. Move the engine switch to the "OFF" position. (Turn
Proper maintenance and service are required to achieve maximum engine life and maintain warranty. The following tables provide
engine specifications as well as maintenance schedules for the generator engines. Note that the generator models are
referenced with the engine model. An engine owner's manual is provided with each machine that also provides basic
maintenance and troubleshooting information. Defer to the engine manufacturers manual if any discrepancies appear between
the data provided in this manual and the engine owner's manual. Full engine service manuals are available from American Honda
Motor Co., 4900 Marconi Drive, Alpharetta, GA 30005-8847, (800) 910-1293.

ENGINE SPECIFICATIONS AND CAPACITIES

Model GX270 (DXGN4500)
Type
Displacement
Bore and Stroke
Net HP
Net Torque
Compression Ratio
Cooling System
Ignition System
Ignition Timing
Spark Plug
Carburetor
Air Cleaner
Lubricating System
Oil Capacity
Starting System
Stopping System
Fuel Type
PTO Shaft Rotation
Dry Weight
English

GENERAL MAINTENANCE

GX340 (DXGN6000)
4-stroke, overhead vale single cylinder, inclined 25°
270cc (16.5 cu in) 389cc (23.7 cu in)
73 x 58 mm
(2.9 x 2.3 in)
8.5 hp @3600rpm 10.7 hp @3600rpm
14.1ft-lb @2500rpm 19.5ft-lb @2500rpm
8.5 : 1
BPR6ES (NGK), W20EPR-U (Nippondenso)
Splash
1.1l (1.16 US qt) 1.1l (1.16 US qt)
Recoil
25.0 kg (55.1 lb)
the key switch to "OFF" on the DXGN14000 model).
4. After the unit has cooled, drain gasoline from fuel tank,
fuel line and carburetor.
5. Pour about one teaspoon of engine oil through the spark
plug hole, pull the recoil starter several times and replace
the plug. Then pull the starter until you feel the piston is
on its compression stroke and leave it in that position. This
closes both the intake and exhaust valves to prevent the
inside of the cylinder from rusting.
6. Cover the unit and store in a clean, dry place that is well
ventilated away from open flame or sparks.
NOTICE:
We recommend always using a fuel
stabilizer. A fuel stabilizer will minimize the formulation of
fuel gum deposits during storage. The fuel stabilizer can
be added to the gasoline in the fuel tank, or into the
gasoline in a storage container.
GX390 (DXGN7200) GX630 (DXGN14000)
389cc (23.7 cu in)
88 x 64 mm 88 x 64 mm
(3.5 x 2.5 in) (3.5 x 2.5 in)
11.7 hp @3600rpm
19.5ft-lb @2500rpm
8.2 : 1
Forced-air
Transistorized magneto
25° B.T.D.C. (fixed)
Horizontal type, butterfly valve
Dual element type
1.1l (1.16 US qt)
Recoil Recoil/Electric
Ignition primary circuit ground
Unleaded gasoline (86 pump octane)
Counterclockwise (from PTO side)
31.5 kg (69 lb) 31.5 kg (69 lb)
15
4-stroke, overhead valve,
V-Twin
688cc (42.0 cu in)
78 x 72 mm
(3.1 x 2.8 in)
20.2hp @3600rpm
35.1ft-lb @2500rpm
8.2 : 1 9.3 : 1
Forced Oil
2.0 l (2.1 US qt)
Electric
44.0 kg (96.8 lb)
0068660