Milwaukee M18 Manuel De L'utilisateur page 56

EXAMPLE:
00
Component Parts (Small #) Are Included
0
When Ordering The Assembly (Large #).
«= Part number change from previous
service parts list.
NOTE: Components of the impacting
assembly (58) can drop out of the
gearcase (54). Care must be taken to
hold those elements in place when
assembling onto
the gearcase end
cap (24).
8
54
4
3
2
1
FIG. PART NO. DESCRIPTION OF PART
1 34-60-0725 Retaining Ring
2 45-88-2026 Washer
3 40-50-1470 Spring
4 45-22-2657 Sleeve
8 45-88-2653 Nylon Washer
9 02-02-0170 4.0mm Steel Ball
10 --------------- 1/4" Hex Anvil
11 02-02-1300 5.0mm Steel Ball
16 02-02-0180 4.7mm Steel Ball
«
22 32-65-2656 Ring Gear
«
24 44-66-0418 Gearcase End Cap with Ball Bearing
25 45-30-2653 Rubber Slug
26 18-01-2657 Field Assembly
31 22-22-2657 Brush Card Assembly
32 45-88-1980 Spring Washer
33 05-88-0926 M3 x 5mm Pan Hd. T-10 Screw
34 40-50-1090 Terminal Block Spring
35 --------------- Handle Halve - Left
37 --------------- Belt Clip
38 06-82-0130 6-32 x 5/16" Pan Hd. T-15 Mach. Screw 1
40 45-24-2657 Forward/Reverse Shuttle
47 42-55-2657 Carrying Case
48 12-20-2618 Service Nameplate
49 --------------- Handle Halve - Right
50 06-82-6350 M3 X 16mm Pan Hd. ST T-10 Screw
«
54 28-50-2658 Gearcase with Bushing
«
55 14-30-2669 Gearcase Assembly
57 23-66-2659 Electronics Assembly - Single Speed
Consists of: On-Off Switch, PCBA,
LED and Battery Terminal Block
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18™ 1/4" Hex Impact Driver - Single Speed
CATALOG NO.
2656-20
62
(1x)
50
(8x)
16
(2x)
1 2 3
75
4 9 10
58
11
9
NOTE: When replacing Gearcase Assembly
(55) on serial break 'A' & 'B' tools, Impact-
10
ing/Anvil Assembly (78) must also be
ordered. DO NOT attempt to use old anvil
1 2 3 4 8
55
and impacting assemblies with new gearcase
9 10 24 54
NO. REQ.
SERVICE PARTS LIST
STARTING
SERIAL NO.
48
74
73
72
25 35 48
70
49 50 62
49
59
47
26
24
80
22
16
22
FIG. PART NO.
«
1 58 14-46-2759
1 59 16-07-2657
1 60 42-70-2653
1 62 06-82-7336
«
1 70 31-44-2661
2 71 ---------------
1 72 ---------------
1 73 ---------------
2 74 ---------------
1 75 42-06-2659
1 76 14-46-2394
8 77 10-20-1126
«
1 80 34-40-0246
1
FIG. LUBRICATION
2
(Type 'J' Grease, No. 49-08-4220):
2
1
1 10 Lightly coat front washer surface of anvil (10) with grease,
1 place a dab in the ball holes of anvil.
22,58 Lightly coat the I.D. of the ring gear (22) and the center of
1
1 the planet gears of impacting assembly with grease.
1
54 Coat inside of bushing inside front gearcase with grease.
1
8
1 59 Coat pinion of armature assembly (59) with grease.
1
1
REVISED BULLETIN
54-26-2502
WIRING INSTRUCTION
F26D
SEE PAGE 2
Brush Card Assy.
73
74
L R
71
32 33 71
31
71
72 73 74
40
35
34
57
37
60
37
38
38
DESCRIPTION OF PART
Impacting Assembly
Armature Assembly
Belt Clip Assembly
4-20 x 3/4" Pan Hd. Plastite T-10 Screw 1
Handle Assembly - Single Speed
Leadwire Assembly - Black - Right Side 1
Leadwire Assembly - Red - Left Side
Brush Spring - Right
Brush Spring - Left
1/4" Hex Anvil Assembly
Leadwire/Screw/Washer Kit
Warning Label (Not Shown)
O-Ring
MILWAUKEE TOOL ● www.milwaukeetool.com
13135 W. Lisbon Road, Brookfield, WI 53005
BULLETIN NO.
54-26-2503
DATE
July 2019
25
Rubber Slugs are (4x)
per handle halve
(8x total)
32
32 33
76
71 72
33
72
NO. REQ.
1
1
1
1
1
2
2
1
1
1
1
Drwg. 1