Settings Overview - Rotel RDG-1520 Manuel De L'utilisateur

14

SETTINGS OVERVIEW

Media Player
FM
DAB
< Settings >
Keep pressing the BACK button to back to the top-level menu. Select the
Setting menu to enter its sub-menu by turning and pressing the knob, it
has 9 setting sub-menus. Turn the knob to find hidden menus.
Network Config
1. Scan for networks
( only for wireless connection)
Turn and push the knob to select this menu. The display will show
"Scanning", which will take a few seconds. Once the network is found,
the display will show the network ID. Turn the knob to select, push to
confirm.
< Scan for networks >
Enter network name
View Config
Edit Config
2. Enter network name
( only for wireless connection)
If the unit can not find any networks, the network ESSID can be entered
manually.
Use the knob to keep selecting letters of the device name by turning
and pressing, and select "END" or hit REPLY on front panel or remote
to confirm the name.
Network Name
< END <> A BCDEFGHIJK >
NAME1
3. View Config
Show current network configuration details. Turn the knob to see next/
previous page of "Mode"-->"ESSID"-->"MAC Address"--> "IP Address"
-->"Netmask"-->"Gateway"-->"DNS Servers". Display as below:
< Mode >
Auto DHCP
4. Edit Config
This menu can be used to edit the current network configuration. This
menu is useful for entering a static IP address. Select this function with
the knob and enter the static IP address, MAC address, DNS of the
selected network.
< Network Config >
Version
Upgrade Firmware
Register
Set Time/Date
FM Tuner
DAB Settings
UPnP
WiFi Strength
< ESSID >
XXXXXX
To enter the value, press knob, then rotate the knob to adjust the value up
or down. Press again to enter the value and move on to the next field.
Continue until all information has been entered.
5. Signal Warning
( only for wireless connection)
Select YES or NO to enable or disable warning of low Wi-Fi signal.
Version
This menu displays software and hardware information of the unit.
Upgrade Firmware
Use this option to download new firmware for the internet radio. If new
firmware is available, there will be a prompt to download.
Note: At this stage, you can press the BACK button to cancel the firmware
upgrade. A firmware upgrade may take several minutes, do not switch
off the power to the unit or put it into standby until the operation is
complete, otherwise, the unit may become permanently damaged.
Upgrading can take 15 to 60 mins, depending on the speed of your
internet connection.
Register
This will display a key that can be used to register the unit on the Rotel
Radio Customer portal: www.rotelradio.com
Set Time/Date
Set you local time and date. Push knob to start entering value, rotate
knob to change value. Press again to confirm value entered and move
on to the next field.
FM Tuner
Select the FM Tuner region with this function.
DAB Setting
There are 3 sub menus: Scan, Clear List, DAB Region. Please select the
menu by turning and pressing the knob.
"Scan" will scan for all available DAB service, it will display list of service
name when successful, or say "no services found " if DAB broadcasting
is not available.
"Clear List" will clear available service list found by "Scan".
"DAB Region" will show regions that provide DAB service, you can select
the desired region by turning and press the knob.
UPnP
Use this setting to set any UPnP device name. This is the name that your
music server will pickup in Media Player mode. Default name is Rotel
Gateway. Use the knob to keep selecting letters of the device name by
turning and pressing, and select "END" word to confirm the name.
DEVICE NAME
< END <> A BCDEFGHIJ >
DEVICE
WiFi Strength
Shows a percentage to indicate the WiFi strength.
RDG-1520 DIGITAL GATEWAY