Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
longer the bar will be from left to right.
DLS
DLS stands for Dynamic Label Segment which is a scrolling message that the broadcaster
may include in their transmissions. The message usually includes information such as
programme details ...etc.
Programme type
This describes the style of the programme that is being broadcast. If the information is
not available, the display will show
"<Program Type>".
Ensemble/Multiplex (Group name)
The Ensemble/Multiplex is a collection of radio stations that are bundled and transmitted together
in a single frequency. There are national and local multiplexes, local ones contain stations that
are specific to that area.
Note: Press and hold the INFO button for longer than 2 seconds, the software version number
will be displayed.
FM RADIO
1. To select FM, repeatedly press the MODE button until you see "Switch to FM" is displayed,
the display will finally show FM
and the frequency.
2.
To activate auto search, turn and hold the SELECT control until it starts to scan the
frequency band, the display will show
"Searching ... > ." or "Searching ... < .", and it will stop automatically once a station has been
found.
3.
To activate manual tuning, repeatedly turn the SELECT control and when you see your
desired frequency appears in the display, release the control.
4.
To select the FM stereo/mono reception mode, press the SELECT button to toggle
between the "Auto" or "Mono" selection.
Note: The radio will automatically switch between the stereo and mono reception, but you can
override this and switch this function manually which is helpful for poor signal reception.
STORING AND RECALLING STORED STATIONS
In either DAB or FM mode, you can store up to 10 stations to the favourite presets; this will
enable you to get direct access to your favourite stations.
1.
To store a preset, first tune to your desired station, then press and hold the PRESET
button until the display shows "Save to P#" and flash.
5
English
2.
press the SELECT button to confirm your selection, the display will show "Preset # saved".
3.
SELECT control to scroll up or down
the presets that you have stored. When the display shows your desired preset number, release
the control. If the preset hasn't been allocated a station, the display will show "Empty preset #".
ALARM FUNCTION (AC operation only)
Setting the alarm time and wake-up mode
1.
SELECT control followed by pressing on the SELECT button to select Alarm (1 or 2).
2.
SELECT button to confirm, the display will show "Alarm # Setting" and the hour digit of the
alarm time will flash.
3.
adjust and confirm your desired alarm time first set the hour and then the minute.
4.
the wake-up mode settings.
5.
to adjust and confirm the wake-up mode settings first set the DAB and FM Preset (1-10),
then the Buzzer Tone (1 or 2), finally the alarm Volume level.
6.
all completed and the alarm function
is now ready for you to activate.
7.
Activating the alarm function
1.
Menu, then turn the SELECT control followed by pressing on the SELECT button to select
Alarm (1 or 2).
2.
selection.
3.
displayed and changed in the below sequence:
6
English
Repeatedly turn the SELECT control to select your desired station preset number then
To recall a preset station, first press the PRESET button once, then repeatedly turn the
This unit incorporates an identical Dual Alarm function in AC operation. You can have
two individual alarm wake-up time and wake-up mode settings to wake you to an
electronic buzzer tone or your favourite radio station (DAB/FM). There is no alarm
function in battery operation.
Press the ALARM button once to enter into the Alarm Menu, then repeatedly turn the
Again repeatedly turn the SELECT control to select "Alarm Setting", then press the
Repeatedly turn the SELECT control followed by pressing on the SELECT button to
After the confirmation of the minute setting, the alarm time is set and you will enter into
Again repeatedly turn the SELECT control followed by pressing on the SELECT button
After the confirmation of the alarm volume level setting, the wake-up mode settings are
Repeat the above procedures to set the other Alarm (1 or 2).
To activate the alarm function, first press the ALARM button to enter into the Alarm
When the display shows "Alarm Source", press the SELECT button to go for the
Repeatedly turn the SELECT control and the associated alarm wake-up mode will be
Publicité
Table des Matières
