Neptun NTP 25 Mode D'emploi page 5

Anleitung NTP 25 06.09.2005
Before start-up, note the Consistency
Your submersible pump is designa-
following!
ted for the circulation of water with
● The pump can be connected to
a maximum temperature of 35° C.
any shock-proof plug which has
This pump may not be used for
been installed according to regu-
other fluids, especially motor fuels,
lations. The plug must have a
cleaning fluids, and other chemical
supply voltage of 230 V ~ 50 Hz.
products!
Fuse min. 6 Amp.
Installation
Caution!
The submersible motor pumps is
installed as follows:
In stagnant water bodies, garden
● In a stationary position with fixed
ponds, swimming ponds and their
pipeline
surrounding areas the pump may
or
only be used with an earth-leakage
● in a stationary position with a fle-
circuit breaker with an actuating
xible hose pipe.
rated current of up to 30 mA (acc.
to VDE 0100 part 702 and 738).
Please note!
The pump is not designed for use
You should never install the pump
in swimmingpools and paddling
by suspending it unsupported from
pools of any kind or other bodies of
its delivery pipe or power cable.
water in which people or animals
The submersible motor pump must
may be present during operation.
be suspended from the specially
It is prohibited to operate the pump
provided handle or be placed on
if a person or animal is in the dan-
the bottom of the shaft. To guaran-
ger area.Ask your electrician!
tee that the pump works properly,
the bottom of the shaft must be
Attention! kept free of sludge and dirt of all
kinds.
(Important for your own security)
If the level of water sinks too far,
Before starting to run your new
any sludge in the shaft will dry out
submersible pump, please have the
quickly and stop the pump from
following items checked by an
starting up. It is necessary, there-
expert:
fore, to check the submersible
● Ground connection
motor pump regularly (by carrying
● Zero conductor
out start-up tests).
● Fault current breaker switch
The floater is adjusted in a way that
must correspond the the
the pump can immediately be star-
safety regulations of the
ted
power plants and they must
work faultessly.
Note!
● The electrical connections must
be protected from moisture. The pump shaft should have mini-
● If there is danger of looding, the
mum dimensions of 40 x 40 x 50
electrical connections must be cm, so that the floating switch can
taken to higher ground.
move freely.
● Circulation of aggressiv fluids, as
Mains supply
well as the circulation of abra-
sive materials must be avoided
Your new submersible pump is
at all costs.
equipped with a shock-proof plug
● The submersible motor-driven
according to regulations. The pump
pump must be protected from
is designed to be connect-ed to a
frost.
220/230 V ~ 50 Hz safety socket.
● The pump must be protected
Make sure that the socket is suffi-
from running dry.
ciently secured (min. 6 Amp.) and
Access on the part of children
is in excellent condition. Introduce
should also be prevented with
the plug into the socket and the
appropriate measures.
pump is ready to go.
10:45 Uhr Seite 5
Important Note!
If the mains cable or plug suffers
any damage from external action,
repairs to the cable are prohibited.
Important!
This work may only be performed
by a qualified electrician or your
ISC GmbH Customer Service.
Areas of use
This pump is used primarily as cel-
lar pump. When installed in a shaft,
this pump provides protection from
flooding.
They are also used wherever water
has to be moved from one place to
another, e.g. in the home, agricul-
ture, horticulture, plumbing and
many other applications.
Setting to work
After having read these instructions
carefully, you can set your pump to
work, reconsidering the following
items:
● Check if the pump rests on the
ground of the shaft.
● Check of pressure cord has
been attached properly .
● Check if electrical connection is
230 V ~ 50 Hz.
● Check if socket is in good
condition.
● Make sure that water and humi-
dity can never come to the
mains supply.
● Avoid pump running dry.
Maintenance guidelines
This submersible pump is an
approuved, maintenance-free high
quality product, which is subject to
severe final controls.
We recommend, regular inspection
and maintenance to ensure long
equipment life and uninterrupted
operation.
GB
5