Télécharger Imprimer la page

EdilKamin INPELLET 49 Installation, Usage Et Maintenance page 33

Masquer les pouces Voir aussi pour INPELLET 49:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 41
st ignition/test by the Edilkamin authorised Dealer
Start-up must be carried out as prescribed by point . 1 of standard NI 1 8 .
This standard indicates the control operations to be carried out in situ, aimed at ascertaining correct system function.
Before igniting.
1st ignition: contact your local Dealer, who will calibrate the insert based on and in compliance with installation conditions.
Failure to have an authorised Edil amin DE LER perform start-up will void the guarantee.
They will calibrate the insert according to the type of pellets available and the conditions of use.
There may be a slight smell of paint the rst few times it is ignited. This will disappear quic ly.
Before igniting, check:
that installation is correct
electricity supply
that the door closes correctly
that the combustion chamber is clean
stand-by indicated on the remote control display: hours (
the tan ) will ash alternately on the display.
Filling the cochlea.
The rst time you use the product, or should the tan be completely emptied of pellets, to ll the coclea press both eys " "
and " " on the remote control at the same time, holding for a few seconds. s you release the eys, the display should show the
wording "LO D". This should be carried out before ignition if the insert has stopped due to having run out of pellets, at the end of
operation to empty the combustion pot before turning.
It is quite normal for some pellets to remain, that the cochlea cannot suction.
Automatic igniting.
ith the insert on stand-by, press and hold the ey
ignition procedure, showing the wording "ST RT".
Ignition is not at a preset time, however: its duration is automatically shortened if the board reports that certain tests have
been passed. The ame appears after about minutes.
Manual igniting.
Temperatures of below
resistance be temporarily out of action, Diavolina type re-starters can be used.
Insert a piece of lit Diavolina into the combustion chamber, close the door and press
PO ER REGULATION
Remote control manual operation
ith the insert wor ing, press the ey " " on the remote control once. The display will show the word "PO ER P".
(specifying the power at which the insert is wor ing). Press the eys " " or " " to increase or decrease the insert s
wor ing power (from "PO ER P1" to "PO ER P ").
Remote control automatic operation
Press ey " " to switch to automatic operation, ad usting the temperature desired for the room (use the " " and " " eys
to set the temperature from
If a temperature below that of the room is set, the insert will stay on "PO ER P1".
Turning off
ith the insert running, press and hold the ey
showing a countdown on the display from 9 to (for a total of 1 minutes).
The turn-off phase involves:
Interruption of pellet supply
a imum ventilation.
Smo e e pulsion motor.
Never pull the plug out whilst the device is still in the process of turning off.
OPERATIONS THAT CAN ONLY BE CARRIED OUT BY REMOTE CONTROL
Clock regulation
Press and hold the ey " " for seconds to access the " loc " menu. This allows you to set the internal electronic board
cloc . By then pressing the ey " ", the following data appears in sequence and can be regulated:
day, month, year, hour, minutes, day of the wee .
INSTRUCTIONS FOR USE
t the same time, a countdown in seconds begins (from 1
will not allow the electrical resistance to heat suf ciently. In this case, or should the
to
, and the insert will regulate wor ing power required to reach the temperature set.
rom the remote control for seconds. The turn-off procedure will begin,
ed display), ambient temperature and the reserve (or g of pellets in
, on the remote control for seconds. This will start-up the
- 33
-
to ).
the remote control.

Publicité

loading

Ce manuel est également adapté pour:

2300l6003