Bosch AKE 30 LI Mode D'emploi page 30

OBJ_BUCH-1275-002.book Page 30 Monday, November 22, 2010 1:10 PM
30 | English
Problem Possible Cause
Saw chain/ No oil in reservoir
guide bar hot
Vent in oil filler cap 4 clogged
Oil passage clogged
Chain tension too high
Dull saw chain
Chain saw rips, Chain tension too loose
vibrates, does
Dull saw chain
not saw proper-
Chain worn out
ly
Chain teeth are facing in the wrong
direction
Excessive vibra- Power tool defective
tions/noise
Sawing time per Too much friction, due to lack of lu-
battery charge bricant
too low
Saw chain needs cleaning
Poor sawing technique
Battery not fully charged
The saw chain is Battery discharged
running slow
Battery stored outside of battery
temperature
Continuous Battery not (properly) inserted
lighting of the
battery charge
Battery contacts contaminated
indicator 24
No charging
procedure pos-
Battery defective
sible
The charge con- Mains plug of battery charger not
trol LEDs 24 plugged in (properly)
and 25 respec-
Socket outlet, mains cable or battery
tively, do not
charger defective
light up after in-
serting the
mains plug into
the socket
Maintenance and Service
Maintenance and Cleaning
Warning: Switch off and remove battery
from power tool before adjusting or
cleaning.
Note: To ensure long and reliable service, car-
ry out the following maintenance regularly.
For safe and proper working, always keep the
power tool and its ventilation slots clean.
Regulary check the chain saw for obvious de-
fects such as loose, dislodged or damaged
saw chain and chain bar, loose fixings and
worn or damaged components.
Check that covers and guards are undamaged
and correctly fitted. Carry out necessary
maintenance or repairs before using.
If the chain saw should fail despite the care
taken in manufacture and testing, repair
should be carried out by an authorised cus-
tomer services agent for Bosch power tools.
Note: Before returning the chain saw, ensure
all oil in the oil reservoir has been emptied.
F 016 L70 758 | (22.11.10)
Corrective Action
Refill oil
Clean oil filler cap 4
Clean oil passage
Adjust chain tension
Sharpen saw chain or replace
Adjust chain tension
Sharpen saw chain or replace
Replace saw chain
Reassemble with chain in correct
direction
Contact Service Agent
Ensure that lubrication is working
(see "Saw-chain Lubrication")
Clean saw chain
see "Working with the Chain Saw"
Recharge battery; also see "Battery
Charging"
Recharge battery; also see "Battery
Charging"
Allow battery to warm naturally to
room temperature (within battery
operating temperature 0 – 45 °C)
Properly insert battery into battery
charger
Clean the battery contacts (e.g. by
inserting and removing the battery
several times) or replace the battery
Replace the battery
Insert mains plug (fully) into the
socket outlet
Check the mains voltage; have the
battery charger checked by an au-
thorised after-sales service agent for
Bosch power tools
In all correspondence and spare parts orders,
please always include the 10-digit article
number given on the type plate of the chain
saw.
Replacing/Changing the Saw Chain and
Chain Bar (see figures C1–C3)
Check the saw chain and chain bar according
to section "Tensioning the Saw Chain".
The circular groove of the chain bar will wear
particularly on the lower edge with time.
When replacing the saw chain, turn the chain
bar by 180° to allow even wear, thus extend-
ing chain bar life.
Check the drive sprocket 28. If it is worn out
or damaged due to strain, have it exchanged
by an authorized Bosch after-sales service.
Sharpening the Saw Chain
Have your chain sharpened professionally at
your authorized Bosch after-sales service or
sharpen the chain yourself using the Bosch
sharpening kit or the Dremel Multi power tool
with the appropriate grinder (1453). Observe
the sharpening instructions provided with the
sharpening kit.
Bosch Power Tools