Safety Instructions For Tile Saw - QEP 60024 Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

SAFETY INSTRUCTIONS FOR TILE
READ THIS OWNER'S MANUAL
GUIDELINES.
1. KEEP GUARDS IN PLACE and in working
2.
REMOVE ADJUSTING KEYS AND WRENCHES.
adjusting wrenches have been removed.
3.
KEEP WORK AREA CLEAN.
4. ALWAYS REMAIN ALERT WHEN THE SAW IS IN USE.
serious injury.
5.
DON'T USE IN A DANGEROUS ENVIRONMENT.
them to rain. Keep work area well lighted.
6.
KEEP CHILDREN AWAY. All visitors should
7.
MAKE WORKSHOP CHILD-PROOF with padlocks, master switches or by
8.
USE RIGHT TOOL.
9.
USE
PROPER EXTENSION CORD.
extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size
to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
10.
DON'T FORCE TOOL. It has been designed to operate at maximum safety and
11.
DO NOT FORCE THE
12.
WEAR PROPER
APPAREL.
get caught in moving parts. Non-slip foot wear is recommended. Wear protective hair covering if you have
long hair.
13. ALWAYS USE SAFETY GLASSES.
for
commercial
eyeglasses only have impact-resistant lenses, they are
safety glasses.
14.
SECURE WORK. Use clamps or a vise instead of your hand to
hold work when practical. This safety precaution allows for
proper tool operation using both hands.
15.
DON'T OVERREACH. Keep
times.
16. MAINTAIN TOOLS WITH CARE.
working condition for maximum safety performance. Follow
instructions for lubricating and changing accessories.
17.
DISCONNECT TOOLS BEFORE
accessories, such as blades, bits, cutters, etc.
18.
REDUCE THE RISK OF UNINTENTIONAL STARTING. Make
sure switch is in OFF position before plugging in.
19.
USE RECOMMENDED ACCESSORIES. Consult the
manual for recommended accessories. The use of improper
accessories may increase risk of injury.
20.
DO NOT
DRY CUT WITH BLADES DESIGNED FOR WET CUTS.
21. MAKE SURE YOU USE THE CORRECT BLADE for the job you
22.
NEVER
STAND ON TOOL.
unintentionally contacted.
23.
CHECK DAMAGED
checked to determine that it will operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect
the saw's operation. A guard or other part that is damaged should be properly repaired or replaced.
24.
ENSURE
THAT THERE IS A CONTINUOUS FLOW OF WATER
25.
CHECK DIAMOND BLADES
ALIGNMENT CONDITION.
cause bodily injury.
26.
DIRECTION OF FEED. Feed work into the blade against the
27.
DO NOT
ALTER THE PLUG OR USE A 2-PRONG RECEPTACLE.
plug.
28.
NEVER
LEAVE TOOL RUNNING UNATTENDED. Turn power off. Don't leave tool until it comes to a
complete stop.
COMPLETELY AND MAKE SURE YOU UNDERSTAND ALL OF IT'S SAFETY
Cluttered areas and benches invite accidents.
Don't force tool or attachment to do a job for which it was not designed.
Make
sure your extension cord is in good condition. When using an
MATERIAL BEING
CUT. Always let the blade cut at its own speed.
Do not wear loose clothing, neckties, rings, bracelets or other
Also use face or dust mask
cutting
operations.
proper footing and balance at all
Keep tools clean and in good
SERVICING
Serious
injury could occur if the tile saw is tipped or if the cutting tool is
PARTS. Before further use of the tool, damaged part(s), (i.e. guard) should be carefully
CAREFULLY FOR CRACKS, NICKS, MISSING DIAMOND MATRIX OR OUT-OF-
Replace damaged blades
SAW
order.
Before turning on the tile saw, make sure the keys and
Inattention on the
Don't use power tools in damp or wet locations or expose
remain at a safe distance from work area.
Everyday
NOT
– when changing
owner's
are doing.
to both sides of blade during operation.
immediately.
direction of rotation of the blade only.
This saw is equipped with a
-
3 -
part of the operator may lead to
removing starter keys.
performance levels.
ILLUSTRATION 1
DRIP LOOP
DO NOT USE DAMAGED BLADES. They may
jewelry which may
3-prong electrical

Publicité

Table des Matières
loading

Table des Matières