Télécharger Imprimer la page

SOLAC CE4552 Mode D'emploi page 8

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
Water will exit through the steamer pipe (G).
Wait until water exits continuously, and push
again over same coffee icon (E1 or E2) to stop
flowing water.
To finish serving, rotate Steam/Water knob (O)
clockwise to close it .
This will complete the priming operation.
FILLING COFFEE:
Remove the filter holder (H).
Position the selected ground coffee filter (J or
K) in the filter holder.
Insert the desired ground coffee filter (J or K)
into the filter holder.
Filter J (smallest) can be used either to ground
or to paper coffee pods.
We recommend using natural toast coffee, as
using some roasted coffee may affect the op-
eration of the machine.
Fill the chosen removable filter (1 or 2 cups)
with ground coffee (6 to 7 gr per cup to be pre-
pared).
Using measuring spoon (I) for 1 coffee, put 1
spoonful.
For POD (single dose of paper), use the same
1coffee filter, placing the monodose well-
placed in the filter.
For 2 coffees, use 2 cups filter and put in 2
spoonful.
Next lightly press down the ground coffee with
the back of the spoon.
Before fitting the filter holder in the coffeemak-
er assembly, move the ladleholder backwards.
Fit the filter holder in the appliance once more.
Position the filter holder in the coffee assembly
by inserting the filterholder from down. Turn it
anticlockwise, from left to right, until it locks.
USE
Before connecting the machine, check that the
steam control (O) is closed.
With Water tank previously filled.
Connect the appliance to the mains.
Turn the appliance ON using the on/off Icon
(F).
The (E1 and E2) icon light will flash intermit-
tently.
Wait until the Icon light (E1 and E2) stop flash-
ing and keep fixed. It means right temperature
is reached.
Place one or two preheated cups at the filter
holder outlet.
Push over desired Coffee Icon (Short, Long).
Corresponding Light will begin to flash.
The unit will start the prebrewing and after a
brief stop, it will continue with the brewing.
The coffee infusion will begin to exit.
When you have got the desired amount of es-
presso coffee (short or long) the machine will
stop automatically.
You always can Stop brewing of coffee push-
ing over Coffee Icon again.
Once serving has finished, wait a few seconds
and remove the cups with the coffee.
Remove the filter holder and empty the
grounds from it.
Wash the filter holder with running water and
dry it well.
Check that the removable filter is perfectly fit-
ted into the filter holder.
Fit the filter holder in the appliance once more.
CHANGING PRESET BREW TIMES
Press the corresponding button (short or long)
for more than 5 seconds, and keep it pressed.
Meanwhile, coffee is exiting until you stop of
pressing. When you Stop, the coffee outlet
time will remain programmed for subsequent
brews.
Always you repeat this operation, machine will
memorize that quantity.
The amount of coffee needed for short or long
coffee may vary from brew to brew depending
on the type of coffee used and how tight it is
pressed. Nevertheless, the programmed brew-
ing times will remain constant.
IMPORTANT NOTICE
The steam tube can be very Hot, Handle with
care during operation. Always grasp the froth-
ing grip to direct the milk foam wand.
GETTING HOT WATER:
Put the device in ON situation, pressing the
ON/OFF Icon (F).
The E1 and E2 Icons will flash, indicating that
the water is heating up.
Wait Until the E1 and E2 Icons light stop. This
situation indicates that the water has reached
the right temperature.
Place a container under the nozzle.
Open the steam control (O), turning him to the
left, counterclockwise.
Press over a Coffee icon (E1 or E2).
EN

Publicité

loading