Maintenance And Care; Repair Service - IKRA Mogatec IART 2520 LI Manuel D'utilisation

Masquer les pouces Voir aussi pour Mogatec IART 2520 LI:

Manuel d'utilisation (89 pages)

Table Des Matières

Table des Matières

Les langues disponibles

Assembly

Attention - risk of injury! Always remove the re-

chargeable battery from the device before all work.

Installing the protective cover (Fig. 3)

If the blade disc is fitted then this must be removed. To do

so loosen the screw (A) (left-handed thread).

Place the protective cover on the strimmer housing such

that both guide bars on the protective cover lie in the

corresponding recesses in the motor housing. Now turn

the protective cover through approx. 30 degrees until it

reaches the correct position.

Attention: request it heeds you that the protective cover-

ing doesn't turn you on the casing around puts down. The

surviving edge must show to the back, to the grip.

Subsequently secure the protective cover with the 2

screws (B) and fit the blade disc.

Attention: After assembly, the protection cover will

permanently remain mounted to the trimmer. The device

must never be operated without protection cover!

Install additional handle (Fig. 4 and 5)

Turn off the knob and remove the threaded bolt from the

included handle. Put the handle onto the tube as shown

in Fig. 4. Slide the handle to the desired position and fix

it using the threaded bolt and knob.

Cutting width indicator/plant protector guard (Fig. 6)

The bar on the front of the strimmer serves as a plant

protector guard and a cutting width indicator. The cutting

blade only moves within the dimensions of the unfolded

bar. However, the strimmer can also be operated with the

bar folded up if required.

Putting the machine in operation

• Insert the charged battery in the strimmer until the

interlock (15) latches. The rechargeable battery can

only be inserted in the strimmer in one position (Fig. 7).

Attention: When inserting the battery do not actuate

the switch-on inhibit (2) and the on/off switch (1).

• Adopt a safe stance. Hold the strimmer in both hands.

Do not set the cutting device down on the ground.

• Press the switch-on inhibit (2) to the left or right and

actuate the switch (1) (Fig. 8). After switching on, the

switch-on inhibit (2) must no longer be held.

• In order to switch off, release the switch (1) (Fig. 8).

Directions for set lenght adjustment and the

use of the set as edge cutter

The tube length may be adjusted to suit your height

(Fig. 9)

• To do so, turn the ribbed plastic sleeve clockwise to

loosen the connection. Adjust the tube to the suitable

length and fasten the connection by turning the tapped

sleeve anti-clockwise.

Adjusting the tilting angle (Fig. 10):

• Press the button (8) - the strimmer head is disengaged

GB | Operating Instructions

(Fig. 7 and 8)

(Fig. 9,10,11,12)

GB-6

and can be pivoted in four positions relative to the

shaft.

Adjusting for edge trimming (Fig.10, 11 and 12):

• Set the tilting angle as previously described.

• Turn the handle (Fig. 11): Lift the plastic cover up-

wards to release (1). It is now possible to turn the

handle through 180° (2). The plastic cover must be

subsequently latched into place again.

Instructions for operating the mowing ma-

chine

(fig. 13)

• Move the mowing machine evenly from oneside to

another.

• If possible, mow by using the left half of the mowing

machine. The mowed parts of plants and / or stones

will thus be hurled forward away from the operating

person.

• The best possible cutting result are achieved when

you hold the trimmer with an angle of 20°- 30° to the

left side.

• Avoid contact between the mowing string and obsta-

cles such as fences, walls, stones, etc. This leads to

excessive wear and tear.

Changing the plastic blade

Attention - risk of injury! Always remove the re-

chargeable battery from the device before all work.

Disassembling the plastic blade:

Push the blade off the retainer stud (1) towards the cen-

tre of the blade disc and remove (2).

Fitting the plastic blade:

Fit the blade over the retainer stud on the blade disc (1)

and pull outwards (2).