Wahl 8467 Mode D'emploi page 6

different-sized attachment combs are included in the
en
scope of supply.
Attaching/removing the attachment comb
All models except 8167:
f Set the adjustment lever to the shortest
cutting length (Fig. 4ⓐ).
1. Place the attachment comb onto the cutting edge of
the blade set and press it down onto the blade set in
the direction of the housing until it clicks into position
(Fig. 5ⓐ).
2. The attachment comb can be easily removed by lifting
the hook in the direction of the arrow (Fig. 5ⓑ).
Maintenance
Cleaning and care
Danger!
Switch off the appliance before cleaning it or
performing any maintenance and disconnect
it from the mains
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the appliance.
f Only reconnect the appliance to the power supply
if it is completely dry.
f Remove the attachment comb (Fig. 5ⓑ) after
every use. Remove the hair clippings from the
blade set with the cleaning brush.
f If a thorough cleaning is required, the
blade set can be removed. See chapter
Changing the blade set.
Oil the blade set with the blade set oil (Fig. 6).
Switch the appliance on briefly (approx. 10 seconds)
to ensure the oil film is evenly distributed.
f For a good and long-lasting cutting perfor-
mance, it is important to oil the blade set
frequently
f If the cutting performance deteriorates after long
use despite regular cleaning and oiling, the blade
set should be replaced.
f Only wipe the appliance with a soft, slightly damp
cloth.
Changing the blade set
Warning! Injuries due to incorrect
handling.
An incorrectly aligned bottom blade can cause
injuries. Ensure that it is properly positioned.
Accessories and spare parts are available from
your dealer or our service centre.
f Undo the screws on the blade set;
remove the bottom blade and the top
blade (Fig. 7).
f When assembling, the bottom blade
and the top blade should be aligned as
follows:
All models except 8167:
Set the adjustment lever to the shortest cutting
length (Fig. 4ⓐ)
f Place the top blade on the plastic cam (Fig. 8).
f Position bottom blade and reinsert the two screws.
f Before tightening the screws, align the bottom
blade so that there is a gap of 0.5 mm to 1.0 mm
between the front edge of the bottom blade and
the front edge of the top blade (Fig. 9).
6
f Tighten screws (Fig. 7).
f Check the alignment of the bottom blade again.
Problem elimination
Blade set is cutting badly.
Blade set is pulling hair out.
Cause: Blade set is dirty.
f Clean and oil the blade set (Fig. 6).
Cause: Blade set is worn out.
f Replace the blade set (Fig. 7/8/9).
Skin injury
Cause: Too much pressure on the skin.
f Less pressure on the skin.
Cause: Cutting angle is too steep.
f Hold appliance flatter to the skin.
Cause: Gap between the front edge of the bottom
blade and the front edge of the top blade is not cor-
rectly aligned.
f Align the bottom blade (Fig. 7).
Appliance is not working.
Cause: Defective power supply.
f Make sure that contact between the appliance plug
and the socket is faultless. Check the mains cable
for possible damage.
In the event that this information does not help you
resolve your problem, please contact our service cen-
tre. Never attempt to repair the appliance yourself!
Disposal
Handle with care! Environmental damage
in the case of incorrect disposal.
f Correct disposal will ensure environmen-
tal protection and prevent any potentially
harmful impacts on people and the
environment.
Adhere to the relevant legal requirements when dis-
posing of the appliance.
Information on the disposal of electrical and elec-
tronic appliances in the European Community:
Within the European Community, national
regulations are specified for the disposal of
electrical appliances based on EU Waste
Electrical and Electronic Equipment Directive
2012/19/EC (WEEE). In accordance with this,
the appliance can no longer be disposed of
with the local or domestic waste. The appli-
ance will be accepted free of charge by local
collection points or recycling centres. The
packaging for this product is made from recy-
clable materials. Dispose of this in an envi-
ronmentally friendly manner by recycling it.