Description - Hilti TE 2 Mode D'emploi

The numbers refer to the illustrations. The illustrations
can be found on the fold-out cover pages. Keep these
pages open while you read the operating instructions.
In these operating instructions, the power tool to which
these operating instructions apply is referred to as "the
tool".

Description

en
The TE 2 / TE 2-E / TE 2-S / TE 2-M is an electrically pow-
ered rotary hammer with pneumatic hammering mech-
anism designed for professional use.
The following items are supplied: power tool, (quick-
release chuck TE 2-M), operating instructions, grease
(except TE 2-E), toolbox, side handle, cleaning cloth,
Depth gauge.
The following conditions must always be observed
when the tool is in use:
– The tool must be connected to an alternating current
electric supply in compliance with the information
given on the type plate.
– The tool is for hand-held use only.
– The tool must not be used in places where the sur-
rounding conditions may present a risk of explosion.
– Changes or modifications to the tool are not per-
missible.
– To avoid the risk of injury, use only the genuine Hilti
The tool is designed for the following uses:
Use
TE 2 / TE 2-E / TE 2-S / TE 2-M:
Hammer drilling in concrete,
masonry and natural stone
TE 2-S:
Drilling with precision
hammering action in perforated – TE-C hammer drill bits
brick, tiles and marble
TE 2 / TE 2-E / TE 2-S:
Drilling in wood, drywall panels Quick-release chuck with TE-C adaptor for insert
and metal
TE 2-M:
Drilling in wood, drywall panels, Interchangeable quick-release chuck for
tiles and metal
12
– Observe the information printed in the operating
– The tool is intended for professional use.The tool
Main features of the tool
Class II electrical protection (double insulated) Z
Mechanical torque-limiting clutch
Grip and side handle with vibration absorption
TE-C chuck
TE-C insert tool system
Variable speed switch
Rotary-only drilling mode
Gearing and hammering mechanism with permanent
grease lubrication
Pivotable side handle (360°)
Mechanical depth gauge
Interface for quick-release chuck (TE 2-M)
Precision hammering action (TE 2-S)
High spindle speed without hammering action (TE 2-M)
Lockbutton for sustained operation
Right of technical changes reserved
Required insert tools
Drill bits with TE-C connection end Drilling in concrete:
– Short hammer drill bits
– Long hammer drill bits
Drill bits with TE-C connection end Drilling in brittle materials:
– Thin-barrel core bits
tools with cylindrical shank or hexagonal shank
for rotary-only drilling
Wood drill bits
Metal drill bits
Hole saws
insert tools with cylindrical shank or hexagonal
shank for rotary-only drilling:
Wood drill bits
Metal/stepped drill bits
Hole saws
accessories and additional equipment specified for
use with this tool.
instructions concerning operation, care and main-
tenance. The tool and its ancillary equipment may
present hazards when used incorrectly by untrained
personnel or when used not as directed.
may be operated, serviced and repaired only by
authorized, trained personnel. This personnel must
be informed of any special hazards that may be
encountered.
Diameter range
Anchor holes of 4–22 mm dia.
Through holes of 4–22 mm dia.
Anchor holes of
Cutting sockets of 25–68 mm dia.
4–20 mm dia.
3–13 mm dia.
25–68 mm dia.
4–10 mm dia. in 2nd gear
10–20 mm dia. in 1st gear
3– 8 mm dia. in 2nd gear
8–13 mm dia. in 1st gear
25–68 mm dia. in 1nd gear
4–22 mm dia.