Blackstar Amplification HT STAGE 100 Manuel Utilisateur page 6

HT STAGE 60-100 HBK 12-12-11:Layout 1 12/12/2011 11:44 Page 10
As the Middle control is increased (clockwise) the amount of 'body' is increased,
which is more suitable for sustained lead guitar tones.
20. Treble
The Treble control allows exact adjustment of the treble frequencies within the sound.
At low settings (counter clockwise) the sound will be warm and darker in character.
As the Treble control is increased (clockwise) the sound will become brighter. At the
maximum settings the sound will be aggressive and cutting.
21. ISF (Infinite Shape Feature)
The patented ISF control works in conjunction with
the Bass, Middle and Treble controls. It allows you to
choose the exact tonal signature you prefer. Fully
counter clockwise has a more American characteristic
with a tight bottom-end and more aggressive middle,
and fully clockwise has a British characteristic which
is more 'woody' and less aggressive.
Unlike conventional 'contour' controls and parametric equalisation systems, the
Bass, Middle and Treble controls remain interactive with each other just like in a
traditional guitar amplifier tone stack. This leads to a very familiar, musical response.
Master
22. Reverb
The Reverb control sets the overall level of the reverb effect. With the control fully
counter clockwise there will be no reverb. Turning the control clockwise will increase
the amount of reverb.
23. Resonance
The Resonance control sets the overall bass response of the amplifier. At lower
settings the cleans will be tight and funky and overdrives will be focussed in their
bass response. At increased settings the clean sounds will become full and warm,
whilst the crunch and overdrive tones will be more bass heavy and resonant.
24. Presence
The Presence control sets the overall treble response of the amplifier. Percussive
high-end can be accentuated on clean sounds and the amount of aggressive treble
controlled with crunch and overdrive settings.
25. Volume
This controls the overall volume of your amplifier. Turning it clockwise increases the
volume.
26. Power Indicator Light
The power indicator will light when the amplifier is switched on.
27. Standby
This switch enables the output stage. Always turn this switch on at least 30 seconds
after the Power switch (28). During short breaks in playing use just this switch to
turn 'off' and 'on' the amplifier's output.
10
USA UK
28. Power
This switch is used to turn the amplifier on and off. You should always turn this switch
on before turning on the Standby switch (27).
Rear Panel
1. Mains Fuse
The value of the Mains Fuse is specified on the rear panel. Never use a fuse of the
incorrect value or attempt to bypass it.
2. Mains Input
The supplied detachable mains lead is connected here. The lead should only be
connected to a power outlet that is compatible with the voltage, power and
frequency requirements stated on the rear panel. If in doubt get advice from a
qualified technician.
3. H.T. Fuse
The value of the H.T. Fuse is specified on the rear panel. Never use a fuse of the
incorrect value or attempt to bypass it.
4. Speaker Outputs
The output marked '1x16 Ohm' is for the connection of a single 16 Ohm extension
speaker cabinet.
The outputs marked '1x8 Ohm or 2x16 Ohm' are for the connection of either a single
8 Ohm extension cabinet or two 16 Ohm cabinets. Also, the internal loudspeaker of
the HT Stage 60 combo can be plugged in here if it is used with a 16 Ohm extension
cabinet.
The outputs marked '1x4 Ohm or 2x8 Ohm' are for the connection of either a single
4 Ohm extension cabinet or two 8 Ohm cabinets. See table below.
'1x16 Ohm'
output
Internal 2x16 Ohm combo speakers X
One 16 Ohm extension cabinet

Two 16 Ohm extension cabinets X
Internal 2x16 Ohm combo speakers X
plus one 8 Ohm extension cab
One 8 Ohm extension cabinet X
Two 8 Ohm extension cabinets X
Single 4 Ohm extension cabinet X
WARNING: The output marked '1x16 Ohm' should never be used at the same time
as any of the outputs marked '1x8 Ohm or 2x16 Ohm' or '1x4 Ohm or 2x8 Ohm'
outputs. The outputs marked '1x8 Ohm or 2x16 Ohm' or '1x4 Ohm or 2x8 Ohm'
outputs should never be used at the same time. Failure to correctly match the
impedance of the amplifier and speakers will damage the amplifier.
'1x8 Ohm or 2x16 '1x4 Ohm or 2x8
Ohm' outputs Ohm' outputs
X X X

X X X X
  X X
X X
 
X X X

X X  
X X  X
11