Remaining Hazards; Machine Specifications; Technical Data; Workpiece Dimensions - Jet 10-20 PLUS Mode D'emploi

Read and understand the entire
instruction manual before attempting
assembly or operation.
Keep this operating instruction close
by the machine, protected from dirt
and humidity, and pass it over to the
new owner if you part with the tool.
No changes to the machine may be
made.
Daily inspect the function and
existence of the safety appliances
before you start the machine.
Do not attempt operation in this case,
protect the machine by unplugging the
power cord.
Before operating the machine, remove
tie, rings, watches, other jewellery, and
roll up sleeves above the elbows.
Remove all loose clothing and confine
long hair.
Wear safety shoes; never wear
leisure shoes or sandals.
Always wear the approved working
outfit:
- safety goggles
- ear protection
- dust protection
Do not wear gloves while operating
this machine.
Install the machine so that there is
sufficient space for safe operation and
workpiece handling.
Keep work area well lighted.
The machine is designed to operate in
closed rooms and must be bolted
stable on firm and levelled table
surface or on the supplied cabinet
stand.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense. Do not operate
the machine when you are tired.
Keep an ergonomic body position.
Maintain a balanced stance at all
times.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Never reach into the machine while it
is operating or running down.
Keep children and visitors a safe
distance from the work area.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Before machining, remove any nails
and other foreign bodies from the
workpiece.
Work only with well sharpened tools.
Machine only stock which rests
securely on the table.
Always close the chuck cover before
you start the machine.
Specifications regarding the maximum
or minimum size of the workpiece
must be observed.
Do not remove chips and workpiece
parts until the machine is at a
standstill.
Do not stand on the machine.
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only.
Have a damaged or worn power cord
replaced immediately.
Make all machine adjustments or
maintenance with the machine
unplugged from the power source.

3.3 Remaining hazards

When using the machine according to
regulations some remaining hazards
may still exist.
The moving sanding drum in the work
area can cause injury.
Drawing-in/trapping hazard by power
feed mechanism.
Squeezing hazard by work piece
power-outfeed.
Thrown workpiece parts can lead to
injury.
Sanding dust and noise can be health
hazards. Be sure to wear personal
protection gear such as safety
goggles, ear plugs and dust mask.
Use a suitable dust exhaust system.
Defective sanding belts can cause
injuries.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.

4. Machine specifications

4.1 Technical data

Drum ( DxL)
Drum speed
Sanding speed
Feed speed
Dust port diameter
suction at 20 m/sec
Net weight
Mains 230V ~1/N/PE 50Hz
Output power 0,75 kW (1HP) S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection

4.2 Workpiece dimensions

Sanding thickness
Max sanding width 255 (510) mm
Min. work piece length

4.3 Noise emission

Acoustic pressure level (EN 11202):
127x255mm
1400 rpm
9,3 m/sec
0 – 3 m/min
100mm
560m3/h
38 kg
5 A
16A
0,8 – 75 mm
60mm