Remaining Hazards; Machine Specifications; Technical Data; Noise Emission - Jet JSSG-8-M Mode D'emploi

Never place your hand near the
cutting area, grinding stone and
honing wheel while machine is in
operation.
Never attempt to hone a tool against
the rotation, the tool will be thrown
away and the honing wheel be
damaged.
Install the machine so that there is
sufficient space for safe operation.
Keep work area well lighted.
The machine is designed to operate in
closed rooms and must be placed
stable on firm and levelled ground.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense. Do not operate
the machine when you are tired.
Keep an ergonomic body position.
Maintain a balanced stance at all
times.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Keep children and visitors a safe
distance from the work area.
Flying sparks can occur when grinding
dry. They can cause injury and ignite
flammable materials.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Normal brushfire might ignite.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Do not force the power tool. It will do
a better and safer job and give you
much better service if it is used at the
rate for which it was designed.
Make sure the tool operates properly.
Periodically check screws and bolts for
tightness.
Never operate with the guards not in
place – serious risk of injury!
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only
Always unwind any extension cords
fully.
Damaged extension cords replace
immediately.
Make certain the switch is in the OFF-
position before connecting the
machine to the power supply.
Do not use the power tool if the
ON/OFF switch does not turn the
power tool ON and OFF.
Make all machine
adjustments or
maintenance with the
machine unplugged from
the power source.
Remove defective abrasive wheels
immediately.
A wet stone may not be placed at
temperatures below 0°C (danger of
freezing).

2.3 Remaining hazards

When using the machine according to
regulations some remaining hazards
may still exist
The moving abrasive wheel in the work
area can cause injury.
Broken abrasive wheels can cause
injuries.
Thrown tools, dust and noise can be
health hazards.
Be sure to wear personal protection
gear such as safety goggles, dust mask
and ear protection.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.
Avoid body contact with earthed or
grounded surfaces (e.g. pipes,
radiators, ranges and refrigerators).

3. Machine specifications

3.1 Technical data

4
Grinding wheel Ø 200x 40x Ø 12mm
Honing wheel
No load speed
Overall L x W x H 330 x 220 x 250mm
Weight
Mains 1~230V, PE, 50Hz
Motor input power
Reference current
Extension cord (H05RN-F)
Installation fuse protection
Isolation class

3.2 Noise emission

(Inspection tolerance 4 dB)
Acoustic power level
(according EN ISO 3744):
Idling LwA 75,2 dB(A)
Acoustic pressure level
(according to EN ISO 11201):
Idling LpA 62,2 dB(A)
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
This information is intended to allow
the user to make a better estimation
of the hazards and risks involved.
3.3 Content of delivery
Slow speed wet sharpener
Stone wheel Ø 200mm, 250 grit
Leather honing wheel Ø 180mm
Water tank
Support arm
Straight edge jig
Stone grader
Honing compound
Angle measuring device
Existing angle measuring device
Operating manual
Spare parts list
DVD

3.4 Machine description

Ø 180x 30mm
100 - 200 rpm
7.8 kg
160W
0,9 A
3x0.75mm²
10A
I