Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Fig 15
Align the drum by turning the fine tune
adjustment knob (D).
When drum is parallel tighten the two
hex socket screws.
Fine tuning drum alignment:
For optimum sanding of boards wider
than the drum, the drum alignment is
critical and must be exactly level to
slightly high on the outboard end.
Turn the board and without changing
the drum height, sand the other end of
the board. If a ridge is visible due to
drum overlap, loosen the tow hex
socket screws (C, Fig 15) and raise
the outboard end of the drum by
turning the fine adjustment knob (D)
slightly clockwise and tighten the two
hex socket screws.
Important:
Only turn the fine tune adjustment
knob when both hex socket screws
are loose.
7.5 Conveyor belt adjustment
To align the tension of the conveyor
belt, first adjust the take-up screw nut
(B, Fig16) on both sides of the
conveyor to obtain approximately
equal tension.
Fig 16
Insufficient tension will cause slippage
of the conveyor belt on the drive roller
during sanding operation.
The belt is too loose when it can be
stopped by hand pressure applied
directly to the top of the conveyor belt.
Belt tracking adjustments are made
while the conveyor belt is running.
After the proper belt tension is
obtained, turn the conveyor on to
fastest speed.
To adjust the belt tracking, tighten the
take-up screw nut (B) on the side the
belt is drifting toward, and loosen the
take-up screw nut on the opposite
side.
Adjust the take-up screw nuts only ¼
turn at a time and allow for the belt to
react before you proceed any further.
Attention:
Do not overtighten the conveyor
belt, as this will reduce the belt life.
7.6 Conveyor belt changing
Disconnect the machine from the
power source (pull mains plug).
Relieve the conveyor belt tension.
Loosen screws (C,D, Fig 16) and
remove the foot plate (A, Fig 6).
Slide conveyor belt off the end of the
conveyor.
Reverse process for installation.
8. Maintenance and inspection
General notes:
Maintenance, cleaning and repair
work may only be carried out after
the machine is protected against
accidental starting by pulling the
mains plug.
Check sanding belts regularly for
faults. Replace a defective sanding
belt immediately.
Inspect the conveyor belt tracking
regularly.
Monthly lubricate all moving parts,
such as threaded rods, washers and
bushings.
Clean the machine regularly.
Blow dust from inside of sanding drum
to prevent vibration (turn the dust
collector on!).
Inspect the proper function of the dust
extraction daily.
Defective safety devices must be
replaced immediately.
All protective and safety devices must
be re-attached immediately after
completed cleaning, repair and
maintenance work.
Repair and maintenance work on the
electrical system may only be carried
out by a qualified electrician.
9. Trouble shooting
Motor doesn't start
*No electricity-
check mains and fuse.
*Defective switch, motor or cord-
consult an electrician.
*Overload has reacted-
Wait and reset overload cut-off.
Reduce federate or stock removal.
Attention: The machine will start
when you reset the overload push
button.
Conveyor belt stops
*Improper belt tension-
Adjust belt tension.
*Shaft coupling loose-
Align shaft flats of gear motor and
tighten shaft coupling set screws.
Board slips on conveyor belt
*Dirty or worn conveyor belt-
Clean or replace conveyor belt.
Machine vibrates excessively
*Dust accumulation on drum inside-
Blow out dust.
Stand on uneven floor-
adjust stand for even support.
Abrasive strip comes off drum
*Slack in abrasive strip on drum-
Tighten abrasive strip.
Sander burns wood
*Depth of cut excessive for fine grit-
Use coarser grit.
*Feed rate too slow-
Increase feed rate.
*Abrasive loaded-
Reduce depth of cut, angle stock.
Clean abrasive with cleaning stick.
*Sanding paper worn-
Avoid area, reverse strip, change
paper.
*Abrasive strip overlapped-
Remove slack in strip.
Sanding marks on the wood
*Uneven federate-
Conveyor belt slipping (see above).
*Wrong grit sanding belt-
use coarser grit for stock removal
and fine grit for finish sanding.
*Drum out of alignment-
Fine-tune drum alignment.
*Machine vibrations (see above)
Publicité
Chapitres
Table des Matières
