AEG NDR 4156 DAB+ Mode D'emploi page 45

Scan DAB stations
Digital Audio Broadcasting (DAB) is a digital broad casing
standard for terrestrial reception of digital radio. A list of radio
stations which can be received in Germany is available on the
Internet at www.digitalradio.de.
NOTE:
In Germany approx. 70 % of the country' s area is covered by
digital radio broadcasts (as of Nov. 2011). In the individual
areas however, coverage and provision vary greatly. If the
DAB stations in your region cannot be received or only with
interferences depending on location, in this case you can
switch to the FM band to receive this station. This is only
possible however if these stations are broadcast via VHF.
Find out more on the internet site of the radio station.
1. Press the FUNCTION button repeatedly until "Connecting"
appears on the display.
2. Press the AUTO SCAN / ENTER button. The device then
searches for the radio stations which can be received.
3. You can select the next or the previous station by using
the UP / DOWN buttons. Press AUTO SCAN / ENTER to
play the selected radio station.
4. If the reception is too weak and the received station
"motorboats", try to improve the reception by changing
the position of the antenna.
NOTE:
To manually set a DAB frequency, proceed as described in
the "Settings menu" sections.
Display additional DAB information
In DAB mode, you can display the following additional
information if broadcast by the radio station. To do so, press
the INFO button.
• DLS: Short for Dynamic Label Segment. This involves
complementary data. This content may be e.g. informa-
tion about the station or the music title and artist being
played.
• This indicates the station category (e.g. Pop-Music, News
etc.).
• Displays the name of the station group (e.g. DR
Deutschland).
• Display of date and time.
• Frequency of the current radio station.
• Displays the digital Audio Bit Rate.
• Displays the received signal strength.
• The "SIGNAL ERROR" display shows the signal quality.
The lower the adjacent figure, the better the quality.
Save station
1. If you have found the desired station, hold down the
PRESET button. The first preset location appears on the
display. When the preset location is empty, (PRESET
EMPTY) is displayed.
NDR 4156 DAB+_K2
2. For choosing the memory position, press UP / DOWN
buttons.
3. Press AUTO SCAN / ENTER to save the settings. The
notification "PRESET SAVED" will briefly appear on the
display.
Select a preset station
1. Press the PRESET button.
2. Press the UP / DOWN buttons to choose a memory
position.
3. Confirm your selection with the AUTO SCAN / ENTER
button.
Settings menu
Numerous settings are made via the Settings menu (see
page 4).
In the Settings menu you can find the main menu and the
related submenus with the individual options.
To enter the menu, keep the SETUP button pressed in DAB
or FM mode.
• Use the UP / DOWN buttons to navigate in the menu.
• Use the AUTO SCAN / ENTER button to select a sub-
menu, or confirm a setting.
• The SETUP button takes you to the previous menu.
NOTE:
• If you do not press any button within 15 seconds, the
menu is hidden.
• The currently set option is highlighted by " ".
A Settings menu can be found in DAB mode, as well as in
FM mode. The DAB and FM menu is explained below along
with the general MAIN MENU menu.
DAB Menu
The DAB menu is divided into menus:
• LOCAL SCAN: Starts the stations scan. The DAB fre-
quency band is scanned for local stations.
• FULL SCAN: Starts the station scan. The DAB frequency
band is scanned for stations.
• MANUAL TUNE: To do so you need to know the station
frequency. This can be found on the internet site of the
broadcasting service. Select the individual frequencies
with the UP / DOWN buttons. Start the manual scan by
pressing the AUTO SCAN / ENTER button. The station
group will appear after a short time on the display. Press
the AUTO SCAN / ENTER again.
FM Menu
The FM SETTINGS menu is divided into menus:
• AUDIO SETTING: Select the desired option for the audio
mode.
English
45
15.06.16