Publicité
Les langues disponibles
Les langues disponibles
Removing Blade
Rotate the blade a quarter turn counter-clockwise
and pull blade out to remove.
OPERATION
Using LED Light
To reduce the risk of injury, do not
WARNING
look directly into the light when the
light is on.
Press the power button
to turn the light on or off.
NOTE: After 15 minutes of continuous use, the light
will shut off automatically.
NOTE: The LED will flash three (3) times to indicate
low batteries. This will continue each time the power
button
is turned on until the batteries are replaced.
Adjusting Force
1. To set the force to LO, push the HI/LO switch to
the left.
2. To set the force to HI, push the HI/LO switch to
the right.
66 Panel/Block/
110 Cross-Connect
Force
Terminal
Panels/Blocks/
Setting
Keystone Jacks
LO
24-26 gauge
All
conductors
HI
23 and larger
NOT
gauge
RECOMMENDED
connectors
110 Type Punchdown
1. Insert the 110 type blade into
the tool.
2. Select the proper force set-
ting by referring to the above
table.
3. Lay the wires in the wire
slots.
4. Place the blade into the wire
slot. Make sure the CUT side
of the blade faces the end of
the wire to be cut.
5. Push down on the back end of
the tool with the palm of your
hand until impact.
6. Remove the blade from the
wire slot. Make sure the wire
is properly seated in the bot-
tom of the wire slot between
the insulation displacement
connector's (IDC) blades.
66 Type Punchdown
1. Insert the 66 type blade into
the tool.
2. Select the proper force
setting by referring to the
above table.
3. Lay the wires in the post
openings.
4. Place the blade into the wire
post. Make sure the CUT side
of the blade faces the end of
the wire to be cut.
5. Push down on the back end of
the tool with the palm of your
hand until impact.
6. Remove the blade from the
wire post. Make sure the wire
is properly seated at the bot-
tom of the post between the
insulation displacement connector's (IDC) blades.
MAINTENANCE
To reduce the risk of injury, always
WARNING
remove the battery before perform-
ing any maintenance. Never disassemble the tool.
Contact a MILWAUKEE service facility for ALL
repairs.
Maintain Tool
Keep your tool in good repair by adopting a regular
maintenance program. If the tool does not work
properly, return the light to a MILWAUKEE service
facility for repairs.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool in liquid or allow a liquid to flow inside
them.
Cleaning
Keep tool handles clean, dry and free of oil or grease.
Use only mild soap and a damp cloth to clean the tool
since certain cleaning agents and solvents are harmful
to plastics and other insulated parts. Some of these
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia and
household detergents containing ammonia. Never
use flammable or combustible solvents around tools.
ACCESSORIES
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Cat. No.
Description
48-22-2166 Extended Reach 110 Punchdown
Blade
48-22-2167 110/66 Combination Punchdown
Blade
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a local distributor.
4
SERVICE - UNITED STATES
1-800-SAWDUST
(1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE hand tool is warranted to the original purchaser
only to be free from defects in material and workmanship. Subject to
certain exceptions, MILWAUKEE will repair or replace any hand tool
which, after examination, is determined by MILWAUKEE to be defec-
tive in material or workmanship for the lifetime of the tool. Return the
hand tool product and a copy of proof of purchase to a MILWAUKEE
factory Service Center location freight prepaid and insured, is required
are requested. A copy of the proof of purchase should be included
with the return product. This warranty does not apply to damage
that MILWAUKEE determines to be from, misuse, alterations, abuse,
normal wear and tear, lack of maintenance or accidents.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT
REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CON-
TRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT.
IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT
PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE
BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL
OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES,
EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSE-
QUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY
PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR
LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EX-
CLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU
OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL.
TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH
DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WAR-
RANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE
EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the 'Service Center Search' in the Parts & Service sec-
tion of MILWAUKEE's website www.milwaukeetool.com or call 1.800.
SAWDUST (1.800.729.3878) to locate your nearest MILWAUKEE
factory Service Center location.
LIMITED WARRANTY - MEXICO,
CENTRAL AMERICA & CARIBBEAN
TECHTRONIC INDUSTRIES' warranty is for 5 years since the original
purchase date.
This warranty card covers any defect in material and workmanship
on this Product.
To make this warranty valid, present this warranty card, sealed/
stamped by the distributor or store where you purchased the product,
to the Authorized Service Center (ASC). Or, if this card has not been
sealed/stamped, present the original proof of purchase to the ASC.
Call toll-free1 01 (800) 030-7777 to find the nearest ASC, for service,
parts, accessories or components.
Procedure to make this warranty valid
Take the product to the ASC, along with the warranty card sealed/
stamped by the distributor or store where you purchased the product,
and any faulty piece or component will be replaced without cost for
you. We will cover all freight costs relative with this warranty process.
Exceptions
This warranty is not valid in the following situations
a) When the product is used in a different manner from the end-user
guide or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modified or repaired by people not authorized
by TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by an Authorized
Service Center to avoid electric risks.
SERVICE AND ATTENTION CENTER
Call to 01 (800) 030-7777
IMPORTED AND COMMERCIALIZED BY
TECHTRONIC INDUSTRIES MEXICO, SA DE CV
Av President Masarik #29 piso 7, Col. Polanco V Sección
CP 11560, Deleg. Miguel Hidalgo, CDMX
Model:
Date of Purchase:
Distributor or Store Stamp:
5
Publicité
