Publicité
•
Test the indicators and tail light for correct function and flash rate.
•
If lights fail to illuminate swap the connectors.
•
Re-fit the pillion seat.
If fitting R&G mini indicators-Not included (Product codes: RG370=Bulb, RG371=LED, RG372=Aero LED)
•
Pass one length of heatshrink (item 7) over the wiring on both mini indicators as shown in picture 13.
Page | 7
•
Place a mini indicator adaptor (item 10) over each indicator ensuring the flat surface sits against the indicator.
•
Pass the mini indicators into the R&G tail bracket (item 1) and secure using the M8 nut included with the
indicators as shown in picture 14.
•
Protect the wiring using an indicator wiring cover (item 4) as shown in picture 15.
•
Pass all three wires through the large heatshrink (item 8) and secure using the small cable ties (item 11) and the
cable tie holes as shown in picture 16. Ensure the cable tie heads sit on the wiring side of the tail bracket.
•
Insert the OEM rubber plug into the tail bracket as shown in picture 17.
•
Mount the tail bracket assembly to the bike using the 4 M6 bolts (item 2) and M6 washers (item 3) as shown in
picture 18.
•
Pass the wiring through the rubber plug as shown in picture 19.
•
On the inside of the seat connect the tail light connector (item 9-CON0043) to the R&G tail light (item 12) using
the bullet connectors.
•
On the inside of the seat connect the two indicator connectors (item 6-CON0014) to the R&G mini indicators
using the bullet connectors.
•
Connect the indicator connectors to their corresponding left and right connectors on the sub-harness removed
earlier.
•
Connect the tail light connector (item 9-CON0043) to the OEM sub-harness.
•
Connect the OEM sub-harness to the motorcycle loom with the connector that was removed in picture 3.
•
Test the indicators and tail light for correct function and flash rate. A resistor (RGR0001/RGR0002-sold
separately may be required to achieve the correct flash rate).
•
If lights fail to illuminate swap the connectors.
•
Re-fit the pillion seat.
Digital copies of these instructions are available to download from
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G
shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or
maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident
or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for
indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service
concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct
from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of
R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 27/04/2018 (HB)
CONSUMER NOTICE
R&G RETURNS POLICY (NON-FAULTY GOODS)
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
R&G
www.rg-racing.com
Email:
www.rg-racing.com
info@rg-racing.com
Publicité
