Last Function Memory; Initialization Of The Microprocessor; Troubleshooting - Denon AVC-A11SR Mode D'emploi

2 Differences in surround mode names depending on the input signals
Sur ound Mode
ANALOG LINEAR PCM DTS 5.1 ch)
PURE DIRECT, DIRECT C C C
STEREO C C C
HOME THX CINEMA THX THX THX MTRX6 1
THX5.1
E E
DTS SURROUND DTS ES MTRX
DTS SURROUND
E
DTS NEO 6 DTS NEO 6 DTS NEO:6
E E E
DOLBY DIGITAL
II E
DOLBY PRO LOGIC DOLBY DOLBY
II II
PRO LOGIC PRO LOGIC
DSP SIMULATION C C C
C : Selectable
: The surround mode name differs depending on the "SB CH OUT" surround parameter setting.
B : The surround mode name differs depending on the input signal.
E : Not selectable
12

LAST FUNCTION MEMORY

• This unit is equipped with a last function memory which stores the input and output setting conditions as they
were immediately before the power is switched off.
This function eliminates the need to perform complicated resettings when the power is switched on.
• The unit is also equipped with a back-up memory. This function provides approximately one week of memory
storage when the main unit's power switch is off and with the power cord disconnected.
13

INITIALIZATION OF THE MICROPROCESSOR

When the indication of the display is not normal or when the operation of the unit does not shows the reasonable
result, the initialization of the microprocessor is required by the following procedure.
1
Switch off the unit using the main unit's power
switch.
2
Press and hold the DIRECT buttons and
STEREO buttons at the same time, and turn the
main unit's power switch on.
3
Check that the entire display is flashing with an
interval of about 1 second, and release your
fingers from the 2 buttons and
microprocessor will be initialized.
NOTES:
• If step 3 does not work, start over from step 1.
• If the microprocessor has been reset, all the
button settings are reset to the default values
(the values set upon shipment from the factory).
Input signals
DTS DOLBY DIG TAL
DTS 96/24(5 1 ch) DTS 6.1 ch) D. D. (2 ch)
C C C
C C C
B
THX5.1 THX DSCRT6 1 THX THX SURROUND EX
THX MTRX5.1
B E
DTS ES MTRX DTS ES DSCRT6 1
DTS 96/24 DTS MTRX6.1
E E
DTS NEO 6
E E E
DOLBY DIGITAL
E E
DOLBY
II
PRO LOGIC
C C C
1, 2 2
the
14

TROUBLESHOOTING

If a problem should arise,first check the following.
1. Are the connections correct ?
D. D. 5.1 ch)
2. Have you operated the receiver according to the Operating Instructions ?
C 3. Are the speakers, turntable and other components operating property ?
If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there
C
may be a malfunction.
Disconnect the power immediately and contact your store of purchase.
THX5.1
E
Symptom
DISPLAY not lit and sound not produced
E
when power switch set to on.
6,1 SURROUND
E
DISPLAY lit but sound not produced.
C
Nothing is displayed on monitor.
No dts sound is produced.
Copying from DVD to VCR is not
possible.
No sound is produced from
subwoofer.
No test tones are produced.
No sound is produced from
surround speakers.
This unit does not operate properly
when remote control unit is used.
Cause Measures
• Power cord not plugged in • Check the insertion of the power
securely. cord plug.
• Speaker cords not securely • Connect securely.
connected.
• Input source selector button • Switch to the proper position.
position is not appropriate.
• Volume control set to minimum. • Turn volume up to suitable level.
• MUTING is on. • Switch off MUTING.
• No digital signal is being input. • Properly select a digital signal input
source.
• Speaker A or B button is set to • Set the button for the connected
"OFF". speaker terminals to "ON".
• AVC-A11SR's video output jacks and • Check that the connections are
monitor's input jacks are not correct.
properly connected.
• Monitor TV's input setting is wrong. • Set the TV's input selector to the
jacks to which video signals are
connected.
• Connections of the various • Unify to composite or S jack.
component's video signals are not
unified.
• VIDEO OFF mode is set. • VIDEO ON mode is set.
• PURE DIRECT mode is set. • Mode other than PURE DIRECT
mode is set.
• DVD player's audio output setting is • Make the DVD player's initial
not set to bit stream. settings.
• DVD player is not dts-compatible. • Use a dts-compatible player.
• AVC-A11SR's input setting is set to • Set to AUTO or dts.
analog.
• Mode video software contains copy • Copying is not possible.
prohibit signals.
• Subwoofer's power is not on. • Turn on the power.
• Subwoofer's initial setting is set to • Set the setting to "Yes".
"No".
• Subwoofer's output is not • Connect properly.
connected.
• Surround mode is set to a mode • Set to Dolby Surround.
other than Dolby Surround.
• Surround mode is set to "STEREO". • Set to a
"STEREO".
• Batteries dead. • Replace with new batteries.
• Remote control unit too far from this • Move closer.
unit.
• Obstacle between this unit and • Remove obstacle.
remote control unit.
• Different button is being pressed. • Press the proper button.
• < and > ends of battery inserted in • Insert batteries properly.
reverse.
ENGLISH
Page
5
8
23
24
23
15
10
5, 6
5, 6
5, 6
26
26
—
—
23
—
—
10
8
—
mode other than —
17
17
17
—
17
35