Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Before Starting Playback
Loading the Batteries in the
Remote Control
1
Open the rear cover.
Press lightly on this
part and slide into the
direction of the arrow.
2
Insert the batteries (AAA/R03 x 2).
Insert as indicated by the / marks into the
battery compartment.
Insert the negative ()
side first.
3
Close the rear cover.
Close securely (a click should be heard).
CAUTION
•
Do not use any batteries other than the ones specified.
Also, do not use a new battery together with an old one.
•
When loading the batteries into the remote control, set
them in the proper direction, as indicated by the polarity
marks ( and ).
•
Do not heat batteries, disassemble them, or throw them
into flames or water.
•
Batteries may have different voltages, even if they look
similar. Do not use different kinds of batteries together.
•
To prevent leakage of battery fluid, remove the batteries
if you do not plan to use the remote control for a long
period of time (1 month or more). If the fluid should leak,
wipe it carefully off the inside of the case, then insert new
batteries. If a battery should leak and the fluid should get
on your skin, flush it off with large quantities of water.
•
When disposing of used batteries, please comply
with governmental regulations or environmental public
institution's rules that apply in your country/area.
•
Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a heater.
This can cause batteries to leak, overheat, explode or
catch fire. It can also reduce the life or performance of
batteries.
12
Approximate operating range of
remote control
Remote control sensor
STANDBY/ON
PQLS
30º
30º
23 ft
Remote control unit
Connecting the Power Cord
Only connect the power cord once all equipment
connections are completed.
AC IN
BDP-43FD
To AC IN terminal
To AC outlet
NOTE
•
Place the Player close to the AC outlet, and keep the
power plug within reach.
•
TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH THE UN-INSULATED PARTS OF ANY CABLES
WHILE THE AC CORD IS CONNECTED.
•
If you are not going to use this Player for a long period of
time, be sure to remove the AC cord from the AC outlet.
Turning the Power On
STANDBY/ON
STANDBY/ON
PQLS
3D
OPEN/CLOSE
FL OFF
USB
5 V
0.5 A
Press STANDBY/ON.
•
Operate using the buttons on either the remote control or
main unit.
•
"POWER ON" appears on the front panel display.
•
When the power is turned on with no disc loaded, the
Pioneer logo screen (wallpaper) is displayed.
•
When the power is turned on with the disc loaded, a menu
screen may be displayed automatically, depending on the
disc.
When
STOP or EXIT is pressed, the disc's menu screen
turns off and the wallpaper is displayed.
Turning the power off
Press STANDBY/ON again.
•
Operate using the buttons on either the remote control or
main unit.
•
"POWER OFF" appears on the front panel display.
•
If you press
STANDBY/ON again immediately after
entering standby, the Player may not turn on. If this
happens, wait for 10 seconds or more and then turn on the
STANDBY/ON again.
Language Setting
Changing the on-screen display
language
1
Press the
HOME MENU to display the HOME
MENU.
•
The HOME MENU is displayed.
2
to select "Settings", then press
Press
ENTER.
to select "On Screen Language",
3
Press
then press ENTER.
4
to select the language you want to
Press
display on the screen, then press ENTER.
English
Español
Français
NOTE
•
To select the DVD disc language, such as subtitle
language, etc., see page 15.
Publicité
Chapitres
Table des Matières
