EINHELL EGS 1800 Instructions De Service page 6

GB
1. Safety regulations
Please remember that improper handling of electrical
equipment may result in hazards which are not always
recognized by children.
Always protect the power station from damp and wet
conditions.
Always switch off the power station when it is not being
used.
Examine the power station for signs of damage before
each use.
Never open the unit. Have repairs carried out by an
electrician.
Do not place on heated surfaces.
Attention: Make sure that the battery clips do not get into
contact!
The person charging the battery must wear protective
goggles.
The person charging the battery must not wear clothes of
synthetic material.
Attention: During the charging process, electrolytic gas
will be released!
Caution: Battery acid is caustic! Splashes on the skin and
the clothes should be removed by washing with soap
water. Splashes of battery acid which have got into your
eyes must be rinsed immediately with water (15 min.),
and a doctor must be consulted.
Important!
The power station is equipped with a maintenance-free
storage battery, which is partially charged when
delivered.
The power station´s storage battery needs to be fully
charged before the unit is used for the first time!
The storage battery discharges automatically when the
power station is not used for a long time.
Use only the supplied power supply unit for charging
purposes.
Environmental protection
Please remember that packaging, old batteries and defective
storage batteries do not belong in your household refuse.
Dispose of these items through the proper channels.
!
2. Scope of delivery
1 power station
1 power supply unit for charging
1 connecting cable with cigarette lighter plug
6
3. Technical data
Storage battery:
Output voltages:
Max. current consumption:
Output voltages:
Max. current consumption:
Starting aid:
Power supply unit:
Mains voltage:
Output from power supply unit:
Nominal voltage:
Nominal current:
Nominal power:
4. Charging the power station with the
power supply unit
1. Set the red „ON/OFF" switch in position „CHA"..
2. Plug the connecting cable of the supplied power supply
unit in the charging socket (INPUT) at the side of the
power station.
3. Plug the power supply unit in a mains socket outlet for
230V~50Hz.
4. The charging time is approximately 24 hours.
5. The red LED (LED 2) lights up in charging mode and
indicates that charging has commenced. When charging
is completed, i.e. when the storage battery is fully
charged, the green LED (LED 1) lights up as well.
5. Outputs
Output 12V cigarette lighter socket:10 amperes max.
(item 6):
These outputs are protected by a 15 ampere blade-type
fuse located at the side of the power station. Replace a
damage fuse only with one of identical amperage.
Remove the caps from the 12V cigarette lighter sockets.
Use the supplied connecting cable to link the 12V output
socket with the unit requiring voltage.
Output 3V / 6V / 9V: 1 ampere max. (item 5):
Stabilization of the 3V, 6V and 9V outputs may be
insufficient forsome electronic appliances (video cameras,
laptops, etc.). We advise you, therefore, to consult your
appliance's operating manual before connecting it.
It is important to note any instructions concerning special
accessories (e.g. 12V adapters for car lighter sockets,
video cameras, etc.) to be found in the operating manual
of the appliance you want to use.
These outputs are protected by a 2 ampere miniature
fuse located at the front of the power station near the
ON/OFF switch. Replace a damaged fuse only with one
of identical amperage.
Check that the voltage and current ratings of the
consumer units will not overload the power station.
Overloading may destroy the power station.
gel battery 12V / 11Ah
3V, 6V, 9V via 6.3mm dia. socket
12V via 2 cigarette lighter sockets
12V / 180A (5 sec.)
230V~50Hz
1A
10A
15V
500mA
7.5VA