Product Presentation; Mounting Kit; Mounting Instructions - CDVI KCPROXWLC Mode D'emploi

INSTALLATION MANUAL
KCPROXWLC
Dual Technology Digicode /Proximity reader
®

1] PRODUCT PRESENTATION

Dual technology:
- Proximity reader,
- Digicode keypad.
®
Output formats:
- Wiegand,
- Standard format,
- ISO Track 2 format.
Stainless steel.
Narrow: Ideal for installation
on aluminium profile.
Backlit.
Recommended for activating
and deactivating your alarm system.
Audible and visual feedback.
Power supplies: 12V dc.
Consumptions: 120mA.
2] NOTES & RECOMMENDATIONS
Operating modes
CENTAUR :
3 operating user modes with CENTAUR:
- Digicode keypad only,
®
- Proximity reader only,
- or dual security (Proximity reader + Digicode keypad).
®
The operating mode is programmed on Centaur software.
TERENA:
There are only 2 operating modes possible
on TERENA:
- Digicode ® keypad,
- Proximity card reader.
Program the proximity card or the pin code
on TERENA software.
Cable
- Programming your installation before installing
products on site.
- The distance between a CTV900A (CENTAUR) controller
or AC22 (ATRIUM) controller and a KCPROXWLC
should not exceed more than 150 meters.
- Make sure not to exceed 50 meters between
the INTBUSW reader interface and the KCPROXWLC
Pin/Prox Digicode ® .
cdvi.com
2
cdvigroup.com
CE Certification
IP64
Environmental tests:
vibrations
-25°C à +60°C
WEEE & RoHS
- Make sure that the cable is not near by a high
voltage cables (ex: 230 V AC).
- Recommended cable 2 twisted pairs (4 wires)
SYT1 0.8MM.
Back EMF protection
To secure the system from back electromagnetic
fields do not forget to mount the varistor in parallel
on the lock terminals.
Security Advice
- For security reasons, change the factory default
master code.
- When selecting a master code and user code
avoid simple codes (example : 3 4 5 6 7).
Mounting recommendations
Mount the keypad on a flat surface to avoid
any vandalism and to insure the best mounting.
Power Supplies
Recommended power supplies: ARD12 or BS60.
These products must be powered in 12Vdc and the
power supply should be certified EN60950-1:2006/
A11:2009 standards and should be designed to be
a low power supply source.
INSTALLATION MANUAL
EN
KCPROXWLC
Dual Technology Digicode

3] MOUNTING KIT

M5x8 Diax
screw
KCPROXWLC

4] MOUNTING INSTRUCTIONS

1
Place the back plate on the
wall then mark with a pen
the hole location then drill
the 2 mounting holes and
the hole wiring access.
5] WIRING EXAMPLE: KCPROXWLC TO A CONTROLLER
KCPROXWLC WIRING TABLE
Wiegand format ISO2 format
Cables
outputs
RED 12VDC Input 12VDC Input
BLACK 0V 0V
Buzzer command Buzzer command
BROWN
input input
GREEN DATA 0 CODE
WHITE DATA 1 DATA
BLUE CLOCK CLOCK
PURPLE PROGRAMMING PROGRAMMING
YELLOW GREEN LED GREEN LED
ORANGE RED LED RED LED
/Proximity reader
®
® T20 Diax ® Plastic
Spanner anchor
1 1
2 3
Insert the 2 plastic anchors Insert the cable in the hole
in the holes. access area of the back
Mount the back plate plate. Then mount the
of the KCPROXWLC with the keypad on the back plate.
screw on the wall.
Controller terminal wirings
Standard format CTV900A
Outputs Outputs
(CENTAUR)
12VDC Input +12V
R1/0V
0V
R2/0V
Buzzer command OUT5
OUT6
input
R1/D0
R2/D0
R1/D1
R2/D1
STANDARD – 1 WIRE
PROGRAMMING
OUT1
GREEN LED
OUT3
OUT2
RED LED
OUT4
EN
M4x30 screw
2 2
4
Fasten the KCPROXWLC
keypad to the back plate
with the M5x8 Diax screw
®
and T20 Diax spanner
®
hardware.
ONLINE SYSTEMS
AC22
INTBUSW
(ATRIUM)
+12V 12
GND V
BUZ 7
D0 1
D1 3
2*
GRN 8
RED 9
* Optional
cdvi.com
3
cdvigroup.com