CDVI KCPROXWLC Mode D'emploi page 5

INSTALLATION MANUAL
KCPROXWLC
Dual Technology Digicode /Proximity reader
®
Default values
- Illumination duration:
10 seconds,
- User code lenght: 5 digits,
- 26 bit wiegand output,
- Buzzer disabled,
- Decimal mode.
Audible Signal
- 1 short beep > keypad powered
and key presses,
- 1 long beep > data computing
in programming,
A] ENTRY IN PROGRAMMING
1. Enter in programming:
- Swich the power supply off,
- Connect the purple cable with the black cable,
- Switch the power supply on.
2. Two beeps are emitted to confirm entry
in programming:
- The keypad is illuminated.
- The red LED is ON.
Note: The command control of the buzzer
is not possible in programming mode.
B] ILLUMINATION DURATION
1. Enter in programming*.
2. Press A0 to program the illumination duration :
- One beep is emitted.
- The Green LED is lighting up during 1 second.
- Enter the time in seconds,
10 for 10 seconds to 99 for 99 seconds
or enter 00 for a permanent illumination.
- One beep is emitted to confirm
the illumination duration.
3. Disconnect the purple cable with the black cable:
Two beeps are emitted to confirm exit
from programming.
C] OUTPUT FORMAT
1. Enter in programming*.
2. Press A1 to enter in the output format menu:
- One beep is emitted.
* Refer to the chapter «Entry in programming».
cdvi.com
8
cdvigroup.com
- 2 short beeps > Entry or Exit
from programming,
- 4 short beeps > data computing error.
Code Length
- In decimal mode, the user code must be in 4,
5 or 6 digits. The keypad key B is used
to validate the programming.
- In ARK mode, all the selected keypad keys
are sending to the controller.
- The Green LED is lighting up during 1 second.
- Press 1 to select wiegand output format
- Press 2 to select Standard output format
- Press 3 to select ISO Track 2 output format
- One beep is emitted to confirm programming.
- The Green LED is lighting up during 1 second.
3. Disconnect the purple cable with the black cable:
Two beeps are emitted to confirm exit
from programming.
D] CODE LENGTH
1. Enter in programming*.
2. Press A2 to enter in the code length
A0
setting menu:
- One beep is emitted.
- The Green LED is lighting up during 1 second.
- Press 4 for a 4-digit user code, press 5
for a 5-digit user code or press 6 for a 6-digit
user code.
- One beep is emitted to confirm programming.
- The Green LED is lighting up during 1 second.
3. Disconnect the purple cable with the black cable:
Two beeps are emitted to confirm exit
from programming.
E] PROGRAMMING THE BIT FORMAT
1. Enter in programming*.
A1
2. Press A3 to select the Bit format:
- One beep is emitted.
- The Green LED is lighting up during 1 second.
- Enter 26, 30 or 44 to define the bit format.
INSTALLATION MANUAL
EN
KCPROXWLC
Dual Technology Digicode
- One beep is emitted to confirm programming.
- The Green LED is lighting up during 1 second.
3. Disconnect the purple cable with the black cable:
Two beeps are emitted to confirm exit
from programming.
F] PROGRAMMING CENTAUR OR STANDARD MODE
1. Enter in programming*.
2. Press A4 to select the mode:
- One beep is emitted.
- The Green LED is lighting up during 1 second.
- Press 0 for a Centaur mode or press 1
for a Standard mode.
- One beep is emitted to confirm programming.
- The Green LED is lighting up during 1 second.
3. Disconnect the purple cable with the black cable:
Two beeps are emitted to confirm exit
from programming.
G] WIEGAND MODE
Decimal or ARK mode affects
only the pin code output format.
1. Enter in programming*.
2. Press A5 to enter in the mode
setting menu:
- One beep is emitted.
- The Green LED is lighting up during 1 second.
- Press 0 for a decimal mode, press 1
A2
for hexadecimal mode and 2 for a ARK mode.
- One beep is emitted to confirm programming.
- The Green LED is lighting up during 1 second.
9] WIEGAND FORMAT
Chronograms
\DATA1
\CLOCK
A3
\DATA0
* Refer to the chapter «Entry in programming».
/Proximity reader
®
3. Disconnect the purple cable with the black cable:
Two beeps are emitted to confirm exit
from programming.
H] AUDIBLE SIGNAL
1. Enter in programming*.
2. Press A6:
- One beep is emitted.
A4
- The Green LED is lighting up during 1 second.
- Press 0 to disable the audible signal.
- Press 1 to enable the audible signal.
- One beep is emitted to confirm programming.
- The Green LED is lighting up during 1 second.
3. Disconnect the purple cable with the black cable:
Two beeps are emitted to confirm exit
from programming.
I] EXTERNAL CONTROL OF THE LED & BUZZER
The buzzer can be activated from an external input.
The control is done with a logic signal on the input.
A5
Buzzer + LED Off
OV
Centaur Mode
LED off. One beep is emitted + Orange LED when
the code is entering. The Buzzer and LED intputs
are activated.
Standard Mode
LED off. The Buzzer and LED intputs are activated.
0 logic 1 logic
50 50
2ms 2ms
μs μs
EN
A6
Buzzer + LED On Buzzer + LED Off
cdvi.com
9
cdvigroup.com