Product Presentation; Reminders And Recommendations; Mounting Kit - CDVI SOLAR2R Mode D'emploi

INSTALLATION MANUAL
SOLAR2R
Dual Technology Digicode
Le SOLAR2R is a controller intended for an access control application

1] PRODUCT PRESENTATION

- dual technology : proximity and Digicode
- remote controller (standalone)
- sensitive touch keypad
- up to 1 000 users
- audible and visual feedback
- 3 relays : 2 doors, 1 alarm
- dimensions (L x W x D) : 130 x 90 x 35 mm
- technology : 125 KHz
- protocol : MARIN
- power supply : 12V dc ± 10%
- consumption* :
• SOLAR2R : 200 mA
• SOLAR2R + 1 TMSOLAR2R : 400 mA
3 operating mode :
- cards + keypad
- cards only
- keypad only 35
*SOLAR2R : remote controller + 1 reader
TMSOLAR2R : 1 reader only (optionnal)

2] REMINDERS AND RECOMMENDATIONS

Wiring reminder
- The distance between a reader and the controller
should not exceed more than 50 meters.
- Make sure that the cable is not near by a high voltage
cables (ex : 230V ac).
- Recommended cable 2 twisted pairs SYT 2P 24 AWG
- Please observe the PE shielding wire connection
Mounting
In order to optimize the fixing of SOLAR2R and to pre-
vent attemps of tearing off please favored flat surfaces.
In configuration 2 drives, keep a minimum distance of
one meter between the 2 readers

3] MOUNTING KIT

Standalone
Controller
SOLAR2R 1
0
TMSOLAR2R
EU Declaration of Conformity : We CDVI declare that the SOLAR2R radio equipment complies
with Directive 2014/53/EU. The full text of the EU declaration is available at www.cdvi.com
/ Proximity Standalone
®
®
90
Reader Foam seal
1 1
1 1
IP53
Vibrations tests
IK10
-30°C à +70°C
Frequency band: 119 - 135 KHz.
Maximum transmitted power <66 dBμA/mA
Ce document est la propritété exclusive de CDVI, il ne peut être communiqué à des tiers sans son autorisation.
This document is the exclusive property of CDVI and it may not be disclosed to others without permission.
F0101000072
C.A. :
SOLARKPW
Plan d'ensemble
Matière : PC V0
Tolérance gale :
Mounting recommendations
DES.: A. Broustal
Vol. (mm
The varistor must be connected directly to the locking
system terminals (electric strikes, electromagnet or
lock).
Security advice
- For security reasons, change the factory default
master code.
- When selecting a master code and user code avoid
simple codes (ex : 3 4 5 6 7).
Recommended power supplies
ADC335 and BS60. These products must be powered
in 12V dc and the power supply should comply with
EN60950-1:2006/A11:2009 standards and should be
designed to be a limited power supply source.
3x30 S5
TF screw Plastic anchor
4 4
2 2
ECHELLE 1:1
A3
0.1 Etat de surface : Ra 3,2
3
) : Poids (g) :
3x8 TORX
TORX bit
®
screw
1 1
1 1
cdvigroup.com
EN
Plan M1849
Edition 00
Date 23/07/2010
Projet : ...
31, av du Gal Leclerc
93691 PANTIN CEDEX
F R A N C E
Tel : 33(0)148910102
Fax : 33(0)148912121
www.cdvi.com
®
7